C350320C102D1G5CA KEMET [Kemet Corporation], C350320C102D1G5CA Datasheet - Page 5

• Manufacturer Part Number: C350320C102D1G5CA
• Description: MILITARY SPECIFCATIONS ON BACK
• Manufacturer: KEMET [Kemet Corporation]

GENERAL SPECIFICATIONS
ELECTRICAL @ 25°C
ENVIRONMENTAL
Working Voltage:
Temperature Characteristics:
Capacitance Tolerance:
Construction:
Lead Material:
Solderability:
Terminal Strength:
Capacitance:
Dissipation Factor:
Insulation Resistance:
Dielectric Withstanding Voltage:
Vibration:
Shock:
C0G
X7R
Z5U
C0G
X7R
Z5U
C0G
X7R
Z5U
Epoxy encapsulated - meets flame test require-
High-temperature solder - meets EIA RS-198D,
Solder Coated Copper Clad Steel
EIA RS-198D, Method 302, Solder temperature -
230° ± 5°C. Dwell time in solder - 7 ± 1/2 seconds.
EIA RS-198D, Method 303, Condition A (2.2 kg)
Within specified tolerance at 25°C and following
test conditions.
At 25°C - same test conditions as capacitance.
EIA RS-198D, Method 104, Condition A
EIA RS-198D, Method 103 (250% of rated voltage
for 5 seconds, with current limited to 50mA)
EIA RS-198D, Method 304, Condition D (10-2000
Hz; 20g)
EIA RS-198D, Method 305, Condition I (100g)
C0G - Greater than 1000 pF with 1.0 vrms at 1 kHz.
X7R - with 1.0 vrms at 1 kHz.
Z5U - with 0.5 vrms at 1 kHz.
C0G - 0.15% maximum
X7R - 2.5% maximum
Z5U - 4.0% maximum
C0G - 100 gigohms or 1000 megohm x µF,
X7R -100 gigohms or 1000 megohm x µF,
Z5U -10 gigohms or 1000 megohm x µF,
CERAMIC CONFORMALLY COATED/AXIAL & RADIAL
ments of UL Standard 94V-0.
Method 302, Condition B (260°C for 10 sec.)
- 1000 pF and less with 1.0 vrms at 1 MHz.
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, [phone]
whichever is less.
whichever is less.
whichever is less.
50 & 100 volts
50 & 100 volts
50 & 100 volts
0 ± 30 PPM/°C from - 55°C to + 125°C
± 15% from - 55°C to + 125°C
+ 22%; - 56% from + 10°C to + 85°C
± 5%, ± 10%, ± 20%
± 10%, ± 20%
± 20%, - 20 + 80%, - 0 + 100%
Axial
PERFORMANCE CHARACTERISTICS
100 & 200 volts
50, 100 & 200 volts
50 & 100 volts
Radial
(1)
(1)
(2)
Life Test:
Moisture Resistance:
Thermal Shock:
EIA RS-198D, Method 201, Condition D. Test
Potential and Temperature.
C0G- 200% of rated voltage at + 125°C
Post-Test Limits at + 25°C are:
Capacitance Change:
Dissipation Factor:
Insulation Resistance:
EIA RS-198D, Method 204, Condition A (10 cycles
without applied voltage.
Post-Test Limits at + 25°C are:
Capacitance Change:
Dissipation Factor:
Insulation Resistance:
EIA RS-198D, Method 202, Condition B (C0G &
X7R: - 55°C to + 125°C; Z5U: - 55°C to + 85°C)
+53 ppm -30 ppm/°C from + 25°C to - 55°C, ± 60
ppm below 10 pF.
X7R & Z5U dielectrics exhibit aging characteristics;
therefore, it is highly recommended that capacitors
be deaged for 2 hours at 150°C and stabilized at
room temperature for 48 hours before capacitance
measurements are made.
X7R - 200% of rated voltage at + 125°C
Z5U - 200% of rated voltage at + 85°C
C0G - ± 3%, or 0.25 pF, whichever is greater.
X7R - ± 20% of initial value.
Z5U - ± 30% of initial value.
C0G - 0.25% maximum
X7R - 3.0% maximum
Z5U - 4.0% maximum
C0G - 10 gigohms or 100 megohm x µF,
X7R - 10 gigohms or 100 megohm x µF,
Z5U - 1 gigohm or 100 megohm x µF,
C0G - 3%, or 0.25 pF, whichever is greater.
X7R - ± 20% of initial value.
Z5U - ± 30% of initial value.
C0G - 0.25% maximum
X7R - 3.0% maximum
Z5U - 4.0% maximum
C0G - 10 gigohms or 100 megohm x µF,
X7R - 10 gigohms or 100 megohm x µF,
Z5U - 1 gigohm or 100 megohm x µF,
whichever is less.
whichever is less.
whichever is less.
whichever is less.
whichever is less.
whichever is less.
(2)
(2)
(2)
(2)
KEMET
5
®