6N140A-100 HP [Agilent(Hewlett-Packard)], 6N140A-100 Datasheet - Page 9

• Manufacturer Part Number: 6N140A-100
• Description: Hermetically Sealed, Low IF, Wide VCC, High Gain Optocouplers
• Manufacturer: HP [Agilent(Hewlett-Packard)]

Notes:
1. GND Pin should be the most negative
2. Output power is collector output
3. Derate I
4. Each channel.
5. CURRENT TRANSFER RATIO is
6. I
7. All devices are considered two-
voltage at the detector side. Keeping
V
than 2.0 V, will provide lowest total
I
power plus total supply power for the
single channel device. For the dual
channel device, output power is
collector output power plus one half
the total supply power. For the quad
channel device, output power is
collector output power plus one
fourth of total supply power. Derate
at 1.66 mW/ C above 110 C.
defined as the ratio of output
collector current, I
LED input current, I
from channel to channel optical
crosstalk. I
test. For all other channels,
I
terminal devices; measured between
all input leads or terminals shorted
together and all output leads or
terminals shorted together.
OHX
OH
F
CC
= 10 mA.
over temperature.
as low as possible, but greater
is the leakage current resulting
F
at 0.33 mA/ C above 110 C.
F
= 2 A for channel under
O
, to the forward
F
, times 100%.
10. CM
11. In applications where dV/dt may
8. Measured between each input pair
9. Measured between adjacent input
shorted together and all output
connections for that channel shorted
together.
pairs shorted together for each multi-
channel device.
the common mode voltage that can be
sustained with the output voltage in
the logic low state (V
is the maximum rate of fall of the
common mode voltage that can be
sustained with the output voltage in
the logic high state (V
exceed 50,000 V/ s (such as a static
discharge) a series resistor, R
should be included to protect the
detector ICs from destructively high
surge currents. The recommended
value is:
R
R
R
for single channel;
for dual channel;
for quad channel.
CC
CC
CC
L
= ——––––––– k
= ——––––––– k
= —–––––—–– k
is the maximum rate of rise of
0.15 I
0.3 I
0.6 I
1 (V)
1 (V)
1 (V)
F
F
F
(mA)
(mA)
(mA)
O
O
< 0.8 V). CM
> 2.0 V).
CC
,
H
14. Parameters tested as part of device
15. The HCPL-6730, HCPL-6731, and
16. Not required for 6N140A, 6N140A/
17. Required for 6N140A, 6N140A/883B,
9
12. This is a momentary withstand test,
13. Standard parts receive 100% testing
not an operating condition.
at 25 C (Subgroups 1 and 9). SMD
and 883B parts receive 100% testing
at 25,125, and -55 C (Subgroups 1
and 9, 2 and 10, 3 and 11,
respectively).
initial characterization and after
design and process changes.
Parameters guaranteed to limits
specified for all lots not specifically
tested.
HCPL-673K dual channel parts
function as two independent single
channel units. Use the single channel
parameter limits.
883B, HCPL-177K, HCPL-6750/51/
5K, 8302401, and 5962-9800201
types.
HCPL-177K, HCPL-6750/51/5K,
8302401, and 5962-9800201 types.