LT6600-2.5_09 LINER [Linear Technology], LT6600-2.5_09 Datasheet
![no-image](/images/no-image-200.jpg)
LT6600-2.5_09
Related parts for LT6600-2.5_09
LT6600-2.5_09 Summary of contents
Page 1
... Chebyshev frequency response. Most differential ampli- fi ers require many precision external components to tail or gain and bandwidth. In contrast, with the LT6600-2.5, two external resistors program differential gain, and the Output fi lter’s 2.5MHz cutoff frequency and passband ripple are RMS internally set ...
Page 2
... LT6600CDF-2.5#TRPBF LT6600IDF-2.5#PBF LT6600IDF-2.5#TRPBF LEAD BASED FINISH TAPE AND REEL LT6600CS8-2.5 LT6600CS8-2.5#TR LT6600IS8-2.5 LT6600IS8-2.5#TR Consult LTC Marketing for parts specifi ed with wider operating temperature ranges. Consult LTC Marketing for information on nonstandard lead based fi nish parts. For more information on lead free part marking, go to: For more information on tape and reel specifi ...
Page 3
... OCM MID LT6600-2.5 + – 1580Ω, and R IN LOAD MIN TYP MAX l –34 –31 l –51 –0.5 –0.1 l –0. –0.2 0.2 l –0.6 0.1 l –2.1 –0.9 l –34 – ...
Page 4
... Note 6: The LT6600C-2.5 is guaranteed functional over the operating temperature range of –40°C to 85°C. ). Note 7: The LT6600C-2.5 is guaranteed to meet specifi ed performance IN from 0°C to 70°C and is designed, characterized and expected to meet specifi ed performance from –40°C and 85°C, but is not tested sampled at these temperatures ...
Page 5
... 1MHz –100 R = 800Ω EACH OUTPUT –110 P-P 660025 G11 LT6600-2.5 Distortion vs Frequency DIFFERENTIAL INPUT, 2ND HARMONIC DIFFERENTIAL INPUT, 3RD HARMONIC SINGLE-ENDED INPUT, 2ND HARMONIC SINGLE-ENDED INPUT, 3RD HARMONIC P 800Ω ...
Page 6
... LT6600-2.5 TYPICAL PERFORMANCE CHARACTERISTICS Distortion vs Input Common Mode Level –40 2ND HARMONIC –50 3RD HARMONIC, GAIN = 2ND HARMONIC, – 3RD HARMONIC, – –80 –90 –100 –110 –3 –2 –1 0 INPUT COMMON MODE VOLTAGE RELATIVE TO V Distortion vs Output Common Mode Level – ...
Page 7
... V common mode voltage of the 1st stage of the fi lter. It has a 5.5kΩ impedance, and it can be overridden with an external low impedance voltage source. – ). The bypass LT6600-2.5 + – to ground and V to ground with – (Pins 6, 7/Pins 4, 5): Output Pins. These ...
Page 8
... LT6600-2.5 BLOCK DIAGRAM – – MID + V 11k 1580Ω 11k – AMP 800Ω + – V OCM + – 800Ω 1580Ω – OCM – OUT PROPRIETARY LOWPASS FILTER STAGE 800Ω + – V OCM + – ...
Page 9
... V and V is the common mode input voltage Similarly, the voltages V and V OUT OUT and 5 of the LT6600-2.5 are the fi lter outputs. The differ- + – ence between V and V is the differential output OUT OUT + voltage. The average of V and V OUT mode output voltage ...
Page 10
... LT6600-2.5 will have lower distortion with larger load resistance yet the analyzer input is typically 50Ω. The 4:1 turns (16:1 impedance) transformer and the two 402Ω resistors of Figure 5, present the output of the LT6600-2.5 with a 1600Ω differential load, or the equivalent of 800Ω to ground at each output. The impedance seen by the network analyzer input is still 50Ω ...
Page 11
... Characteristics”). Common Mode DC Currents . In applications like Figure 1 and Figure 3 where the LT6600-2.5 MID not only provides lowpass fi ltering but also level shifts the common mode voltage of the input signal, DC currents ...
Page 12
... There is a need to ensure that the die’s junction temperature does not exceed 150°C. The LT6600-2.5 S8 package has Pin 6 fused to the lead frame to enhance thermal conduction when connect- ing to a ground plane or a large metal trace. Metal trace and plated through-holes can be used to spread the heat generated by the device to the backside of the PC board ...
Page 13
... APPLICATIONS INFORMATION – to the V pin to provide a heat sink, the thermal resistance will be around 105°C/W. Table 3 can be used as a guide when considering thermal resistance. Table 3. LT6600-2.5 SO-8 Package Thermal Resistance COPPER AREA TOPSIDE BACKSIDE BOARD AREA (mm2) (mm2) (mm2) 1100 1100 2500 ...
Page 14
... LT6600-2.5 PACKAGE DESCRIPTION 3.38 ±0.05 4.50 ± 0.05 2.65 ± 0.05 3.10 ± 0.05 RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED PIN 1 TOP MARK (NOTE 6) 0.200 REF NOTE: 1. DRAWING IS PROPOSED TO BE MADE A JEDEC PACKAGE OUTLINE MO-220 VARIATION (WGGD-X)—TO BE APPROVED 2. DRAWING NOT TO SCALE 3 ...
Page 15
... TYP .016 – .050 .014 – .019 (0.406 – 1.270) (0.355 – 0.483) TYP INCHES (MILLIMETERS) LT6600-2.5 .189 – .197 (4.801 – 5.004) NOTE .150 – .157 (3.810 – 3.988) ...
Page 16
... McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 ● 5th Order Lowpass Filter (S8 Pin Numbers Shown 0.1μ – – LT6600 C 2 – 0.1μ 2π • R • 2.5MHz 1580Ω – GAIN = ...