LTC1287 LINER [Linear Technology], LTC1287 Datasheet - Page 14
![no-image](/images/no-image-200.jpg)
LTC1287
Manufacturer Part Number
LTC1287
Description
3V Single Chip 12-Bit Data Acquisition System
Manufacturer
LINER [Linear Technology]
Datasheet
1.LTC1287.pdf
(16 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTC1287CCN8
Manufacturer:
TI
Quantity:
190
LTC1287
A
noise is insignificant with a 2.5V reference input but will
become a larger fraction of an LSB as the size of the LSB
is reduced. The Typical Performance Characteristics
curve of Noise Error vs Reference Voltage shows the
LSB contribution of this 200 V of noise.
For operation with a 2.5V reference, the 200 V noise is
only 0.32LSB peak-to-peak. Here the LTC1287 noise
will contribute virtually no uncertainty to the output
code. For reduced references, the noise may become a
significant fraction of an LSB and cause undesirable
jitter in the output code. For example, with a 1.25V
reference, this 200 V noise is 0.64LSB peak-to-peak.
This will reduce the range of input voltages over which
a stable output code can be achieved by 0.64LSB. Now
averaging readings may be necessary.
This noise data was taken in a very clean test fixture.
Any setup induced noise (noise or ripple on V
or V
reference voltage used, the more critical it becomes to
have a noise-free setup.
Overvoltage Protection
Applying signals to the LTC1287’s analog inputs that
exceed the positive supply or that go below ground will
degrade the accuracy of the A/D and possibly damage
the device. For example this condition would occur if a
signal is applied to the analog inputs before power is
applied to the LTC1287. Another example is the input
source operating from different supplies of larger value
than the LTC1287. These conditions should be pre-
vented either with proper supply sequencing or by use
of external circuitry to clamp or current limit the input
source. There are two ways to protect the inputs. In
Figure 15 diode clamps from the inputs to V
are used. The second method is to put resistors in
series with the analog inputs for current limiting. Limit
the current to 15mA per channel. The +IN input can
accept a resistor value of 1k but the –IN input cannot
accept more than 200 when clocked at its maximum
clock frequency of 500kHz. If the LTC1287 is clocked at
the maximum clock frequency and 200 is not enough
to current limit the input source then the clamp diodes
are recommended (Figures 16 and 17). The reason for
14
PPLICATI
IN
) will add to the internal noise. The lower the
O
U
S
I FOR ATIO
U
W
CC
and GND
U
CC
, V
REF
the limit on the resistor value is the MSB bit test is
affected by the value of the resistor placed at the –IN
input (see discussion on Analog Inputs and the Typical
Performance Characteristics curve of Maximum CLK
Frequency vs Source Resistance).
If V
be turned on first, then V
met, connecting a diode from V
mended (see Figure 18).
Because a unique input protection structure is used on
the digital input pins, the signal levels on these pins can
exceed the device V
CC
and V
1N4148 DIODES
Figure 17. Overvoltage Protection for Inputs
Figure 15. Overvoltage Protection for Inputs
Figure 16. Overvoltage Protection for Inputs
REF
1k
1N4148 DIODES
200
1k
are not tied together, then V
CC
CS
+IN
without damaging the device.
–IN
GND
CS
+IN
–IN
GND
REF
LTC1287
CS
+IN
–IN
GND
LTC1287
. If this sequence cannot be
LTC1287
D
V
V
CLK
D
OUT
V
REF
CLK
V
CC
OUT
REF
CC
D
V
CLK
REF
V
OUT
REF
CC
to V
+3V
LTC1287 F16
LTC1287 F17
CC
LTC1287 F15
+3V
+3V
CC
is recom-
should