NC2D-DC110V NAIS [Nais(Matsushita Electric Works)], NC2D-DC110V Datasheet - Page 11

• Manufacturer Part Number: NC2D-DC110V
• Description: FLAT/VERTICAL TYPE HIGH POWER BIFURCATED CONTACT
• Manufacturer: NAIS [Nais(Matsushita Electric Works)]

NC4-SS
NC4-L2S
NC4-PS
NC4-L2P
NOTES
1. To maintain insulation between coils of
2 coil latching series, terminals 5 and 6 for
flat series, and terminals 3 and 4 for slim
series should be connected to provide
common return.
2. 2 coil latching series 4C are for intermit-
tent operation only. Power should be ap-
plied to coils continuously for no more
than two minutes.
3. When designing printed circuit board
patterns, note that:
(1) "Top View" wiring diagram is indicated
for the Flat series because terminals can
be seen from above.
For Cautions for Use, see Relay Technical Information (Page 48 to 76).
9/1/2000
Set switch
Set coil
5
4
6
Reset coil
3
Reset switch
1.732
44.0
1.732
44.0
Terminal width: 1.9
Terminal thickness: 0.4
Terminal width: 0.9
Terminal thickness: 0.4
12.6
.496
12.6
.496
Terminals 3 and 6 excluded for NC4-SS.
Terminals 3 and 6 excluded for NC4-PS.
20.4
.803
.154
20.4
.803
.154
(2) "Bottom View" wiring diagram is indi-
cated for the Slim series because termi-
nals can not be seen from above.
4. When using slim series in close proxim-
ity, mount all relays facing the same direc-
tion.
Different mounting directions may cause
change in the relay characteristics be-
cause NC relays are polarized.
3.9
3.9
.075
.035
.339
8.6
.039
1.0
.339
.039
8.6
1.0
.016
.016
.315
8.0
.181
General tolerance: 0.5
General tolerance: 0.5
4.6
1.654
42.0
30.48
1.200
30.48
1.200
20.32
.800
20.32
.800
10.16
.400
10.16
.400
5.08
.200
.200
5.08
Same direction
11.2
.441
7.62
.300
11.2
.441
All Rights Reserved, © Copyright Matsushita Electric Works, Ltd.
7.62
.300
.020
.020
5.08
.200
5.08
.200
15.24
.600
15.24
.600
1.000
25.4
1.000
25.4
35.56
1.400
35.56
1.400
1.654
42.0
5. Sockets
(1) When PC board series are used with
socket, do not apply loads exceeding 3 A.
(2) Soldering should be done quickly to
avoid damaging the thermoplastic body.
(3) Insulation will be optimum when wire
connections are soldered as shown with
all slim sockets.
Chassis thickness range: 1.0 to 2.0
.300
2.54
.100
7.62
(copper-side view)
PC board pattern
9 10 11 12 13 14 15 16
Chassis cutout
8
2.54
.100
7
11.5
.453
6 5 4 3 2 1
Go To Online Catalog
0.5
.020
1.673
42.5
Tolerance: 0.1
.039 to .079
16-1.2 DIA. HOLES
16-.047 DIA. HOLES
NC
.004
233