LTC2207 LINER [Linear Technology], LTC2207 Datasheet - Page 6

• Manufacturer Part Number: LTC2207
• Description: 16-Bit, 105Msps/80Msps ADCs
• Manufacturer: LINER [Linear Technology]

LTC2207/LTC2206
TIMING CHARACTERISTICS
range, otherwise specifi cations are at T
SYMBOL PARAMETER
f
t
t
t
t
t
t
t
Pipeline
Latency
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: All voltage values are with respect to GND, with GND and OGND
shorted (unless otherwise noted).
Note 3: When these pin voltages are taken below GND or above V
will be clamped by internal diodes. This product can handle input currents
of greater than 100mA below GND or above V
Note 4: V
differential ENC
input range = 2.25V
specifi ed.
Note 5: Integral nonlinearity is defi ned as the deviation of a code from a
TIMING DIAGRAM
6
S
L
H
AP
D
C
SKEW
OE
DD
Sampling Frequency
ENC Low Time
ENC High Time
Sample-and-Hold
Aperture Delay
ENC to DATA Delay
ENC to CLKOUT Delay
DATA to CLKOUT Skew
DATA Access time
Bus Relinquish time
= 3.3V, f
+
/ENC
P-P
SAMPLE
–
= 2V
with differential drive (PGA = 0), unless otherwise
D0-D15, OF
CLKOUT
CLKOUT
ANALOG
P-P
INPUT
= 105MHz (LTC2207), 80MHz (LTC2206)
ENC
ENC
sine wave with 1.6V common mode,
–
+
+
–
CONDITIONS
(Note 9)
Duty Cycle Stabilizer Off (Note 7)
Duty Cycle Stabilizer On (Note 7)
Duty Cycle Stabilizer Off (Note 7)
Duty Cycle Stabilizer On (Note 7)
(Note 7)
(Note 7)
(t
CL = 5pF (Note 7)
(Note 7)
C
N
-t
A
DD
D
t
H
= 25°C. (Note 4)
) (Note 7)
without latchup.
t
t
t
AP
D
C
N – 7
t
L
N + 1
The
●
DD
denotes the specifi cations which apply over the full operating temperature
, they
N – 6
N + 2
“best fi t straight line” to the transfer curve. The deviation is measured from
the center of the quantization band.
Note 6: Offset error is the offset voltage measured from –1/2LSB when the
output code fl ickers between 0000 0000 0000 0000 and 1111 1111 1111
1111 in 2’s complement output mode.
Note 7: Guaranteed by design, not subject to test.
Note 8: V
input range = 2.25V
Note 9: Recommended operating conditions.
Note 10: The dynamic current of the switched capacitors analog inputs
can be large compared to the leakage current and will vary with the sample
rate.
Note 11: Leakage current will have higher transient current at power up.
Keep drive resistance at or below 1Kohm.
●
●
●
●
●
●
●
●
●
●
N – 5
DD
5.94
4.06
5.94
4.06
–0.6
MIN
1.3
1.3
1
= 3.3V, f
N + 3
LTC2206
6.25
6.25
6.25
6.25
–0.7
TYP
P-P
2.7
2.7
SAMPLE
0
5
5
7
with differential drive.
N – 4
= 105MHz (LTC2207) or 80MHz (LTC2206),
MAX
500
500
500
500
0.6
80
15
15
4
4
N – 3
N + 4
MIN
4.52
3.10
4.52
3.10
–0.6
1.3
1.3
1
22076 TD01
LTC2207
4.762
4.762
4.762
4.762
–0.7
TYP
2.7
2.7
0
5
5
7
MAX
105
500
500
500
500
0.6
15
15
4
4
UNITS
Cycles
22076fa
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns