CAT24WC01 Catalyst Semiconductor, CAT24WC01 Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/1/126/catalyst_semiconductor_sml.jpg)
CAT24WC01
Manufacturer Part Number
CAT24WC01
Description
1K/2K/4K/8K/16K-Bit Serial E2PROM
Manufacturer
Catalyst Semiconductor
Datasheet
1.CAT24WC01.pdf
(9 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CAT24WC01J-TE13
Manufacturer:
HOLTEK
Quantity:
6 000
Part Number:
CAT24WC01J-TE13
Manufacturer:
CATALYST
Quantity:
20 000
Part Number:
CAT24WC01JI
Manufacturer:
CATALYS
Quantity:
20 000
Company:
Part Number:
CAT24WC01JI-TE13
Manufacturer:
ON
Quantity:
9 200
Company:
Part Number:
CAT24WC01LI
Manufacturer:
CSI
Quantity:
26 000
Part Number:
CAT24WC01LI
Manufacturer:
CATALYST
Quantity:
20 000
Part Number:
CAT24WC01W
Manufacturer:
CATALYST
Quantity:
20 000
Figure 5. Slave Address Bits
*
**
*** A0, A1 and A2 must compare to its corresponding hard wired input pins (pins 1, 2 and 3).
line) when its address matches the transmitted slave
address. The CAT24WC01/02/04/08/16 then performs
a Read or Write operation depending on the state of the
R/W bit.
Acknowledge
After a successful data transfer, each receiving device is
required to generate an acknowledge. The Acknowledg-
ing device pulls down the SDA line during the ninth clock
cycle, signaling that it received the 8 bits of data.
The CAT24WC01/02/04/08/16 responds with an ac-
knowledge after receiving a START condition and its
slave address. If the device has been selected along
with a write operation, it responds with an acknowledge
after receiving each 8-bit byte.
When the CAT24WC01/02/04/08/16 is in a READ mode
it transmits 8 bits of data, releases the SDA line, and
monitors the line for an acknowledge. Once it receives
this acknowledge, the CAT24WC01/02/04/08/16 will
continue to transmit data. If no acknowledge is sent by
the Master, the device terminates data transmission and
waits for a STOP condition.
Doc. No. 25051-00 3/98 S-1
A0, A1 and A2 correspond to pin 1, pin 2 and pin 3 of the device.
a8, a9 and a10 correspond to the address of the memory array address word.
24WC01/02
24WC04
24WC08
24WC16
1
1
1
1
0
0
0
0
1
1
1
1
6
WRITE OPERATIONS
Byte Write
In the Byte Write mode, the Master device sends the
START condition and the slave address information
(with the R/W bit set to zero) to the Slave device. After
the Slave generates an acknowledge, the Master sends
the byte address that is to be written into the address
pointer of the CAT24WC01/02/04/08/16. After receiving
another acknowledge from the Slave, the Master device
transmits the data byte to be written into the addressed
memory location. The CAT24WC01/02/04/08/16 ac-
knowledge once more and the Master generates the
STOP condition, at which time the device begins its
internal programming cycle to nonvolatile memory. While
this internal cycle is in progress, the device will not
respond to any request from the Master device.
Page Write
The CAT24WC01/02/04/08/16 writes up to 16 bytes of
data in a single write cycle, using the Page Write
operation. The Page Write operation is initiated in the
same manner as counter will ‘wrap around’ to address
0
0
0
0
A2
a10
A2
A2
A1
A1
a9
a9
A0
a8
a8
a8
R/W
R/W
R/W
R/W