X1227 Xicor, X1227 Datasheet - Page 2

• Manufacturer Part Number: X1227
• Description: Real Time Clock/Calendar/CPU Supervisor with EEPROM
• Manufacturer: Xicor

X1227
DESCRIPTION (continued)
The Real-Time Clock keeps track of time with separate
registers for Hours, Minutes, Seconds. The Calendar
has separate registers for Date, Month, Year and Day-
of-week. The calendar is correct through 2099, with
automatic leap year correction.
The powerful Dual Alarms can be set to any Clock/
Calendar value for a match. For instance, every
minute, every Tuesday, or 5:23 AM on March 21. The
alarms can be polled in the Status Register. There is a
repeat mode for the alarms allowing a periodic
interrupt.
The X1227 device integrates CPU Supervisor func-
tions and a Battery Switch. There is a Power-On Reset
(RESET output) with typically 250 ms delay from power
on. It will also assert RESET when Vcc goes below the
specified threshold. The V
grammable. There is a WatchDog Timer (WDT) with 3
selectable time-out periods (0.25s, 0.75s, 1.75s) and a
disabled setting. The watchdog activates the RESET
pin when it expires.
The device offers a backup power input pin. This
V
or SuperCap. The entire X1227 device is fully
operational from 2.7 to 5.5 volts and the clock/calendar
portion of the X1227 device remains fully operational
down to 1.8 volts (Standby Mode).
The X1227 device provides 4K bits of EEPROM with 8
modes of BlockLock™ control. The BlockLock allows a
safe, secure memory for critical user and configuration
data, while allowing a large user storage area.
PIN DESCRIPTIONS
REV 1.1.20 1/13/03
NC = No internal connection
BACK
pin allows the device to be backed up by battery
RESET
V
V
BACK
X1
X2
V
SS
CC
X1
X2
8-Pin TSSOP
8-Pin SOIC
1
2
3
4
1
2
3
4
X1227
X1227
trip
8
7
6
5
threshold is user repro-
8
7
6
5
SCL
SDA
V
RESET
SS
V
V
SCL
SDA
CC
BACK
www.xicor.com
Serial Clock (SCL)
The SCL input is used to clock all data into and out of
the device. The input buffer on this pin is always active
(not gated).
Serial Data (SDA)
SDA is a bidirectional pin used to transfer data into and
out of the device. It has an open drain output and may
be wire ORed with other open drain or open collector
outputs. The input buffer is always active (not gated).
An open drain output requires the use of a pull-up
resistor. The output circuitry controls the fall time of the
output signal with the use of a slope controlled pull-
down. The circuit is designed for 400kHz 2-wire inter-
face speeds.
V
This input provides a backup supply voltage to the
device. V
event the V
to a battery, a Supercap or tied to ground if not used.
RESET Output – RESET
This is a reset signal output. This signal notifies a host
processor that the watchdog time period has expired or
that the voltage has dropped below a fixed V
old. It is an open drain active LOW output. Recom-
mended value for the pullup resistor is 5K Ohms. If
unused, tie to ground.
X1, X2
The X1 and X2 pins are the input and output,
respectively, of an inverting amplifier. An external
32.768kHz quartz crystal is used with the X1227 to
supply a timebase for the real time clock. The
recommended crystal is a Citizen CFS206-32.768KDZF.
Internal compensation circuitry is included to form a
complete oscillator circuit. Care should be taken in the
placement of the crystal and the layout of the circuit.
Plenty of ground plane around the device and short
traces to X1 and X2 are highly recommended. See
Application section for more recommendations.
Figure 1. Recommended Crystal connection
BACK
BACK
CC
supply fails. This pin can be connected
supplies power to the device in the
Characteristics subject to change without notice.
X1
X2
TRIP
thresh-
2 of 28