ADV7197KST Analog Devices, ADV7197KST Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
ADV7197KST
Manufacturer Part Number
ADV7197KST
Description
Multiformat HDTV Encoder with Three 11-Bit DACs
Manufacturer
Analog Devices
Datasheet
1.ADV7197KST.pdf
(20 pages)
ADV7197
FUNCTIONAL DESCRIPTION
Digital Inputs
The digital inputs of the ADV7197 are TTL-compatible. 30-bit
YCrCb or RGB pixel data in 4:4:4 format or 20-bit YCrCb pixel
data in 4:2:2 format is latched into the device on the rising edge
of each clock cycle at 74.25 MHz or 74.1758 in HDTV mode.
It is recommended to input data in 4:2:2 mode to make use of
the Chroma SSAFs on the ADV7197. As can be seen in the
figures below, these filters have 0 dB passband response and
prevent signal components being folded back into the frequency
band. In 4:4:4 input mode, the video data is already interpo-
lated by an external input device and the chroma SSAFs of the
ADV7197 are bypassed.
Control Signals
The ADV7197 accepts sync control signals accompanied by
valid 4:2:2 or 4:4:4 data. These external horizontal, vertical and
blanking pulses (or EAV/SAV codes) control the insertion of
appropriate sync information into the output signals.
Analog Outputs
The analog Y signal is output on the 11-bit + Sync DAC A,
the color component analog signals on the 11-bit DACs B, C
conforming to EIA-770.3 standards R
ATTEN
RL –10.0dBm
START 100kHz
ATTEN
RL –10.0dBm
START 100kHz
RBW 10kHz
RBW 10kHz
10dB
10dB
VBW 300Hz
VBW
VAVG
VAVG
10dB/
10dB/
1
4
300Hz
3.18MHz
3.12MHz
STOP
STOP
MKR
MKR
SET
0dB
20.00MHz
–3.00dB
20.00MHz
SWP
has a value of 2470 Ω
SWP 17.0SEC
17.0SEC
(EIA-770.3), R
form to RS-170/RS-343A standards R
of 2820 Ω.
Internal Test Pattern Generator
The ADV7197 can generate a Cross-Hatch pattern (white lines
against a black background). Additionally, the ADV7197 can
output a uniform color pattern. The color of the lines or uni-
form field/frame can be programmed by the user.
Y/CrCb Delay
The Y output and the color component outputs can be delayed
wrt the falling edge of the horizontal sync signal by up to four
clock cycles.
I
A selectable internal I
on the I
width on the I
are not passed to the I
greater input bandwidth on the I
MPU PORT DESCRIPTION
The ADV7197 support a 2-wire serial (I
processor bus driving multiple peripherals. Two inputs Serial
Data (SDA) and Serial Clock (SCL) carry information between
any device connected to the bus. Each slave device is recognized
by a unique address. The ADV7197 has four possible slave
addresses for both read and write operations. These are unique
addresses for each device and are illustrated in Figure 8. The LSB
sets either a read or write operation. Logic Level “1” corresponds
to a read operation while Logic Level “0” corresponds to a write
operation. A1 is set by setting the ALSB pin of the ADV7197 to
Logic Level “0” or Logic Level “1.” When ALSB is set to “0,”
there is greater input bandwidth on the I
high-speed data transfers on this bus. When ALSB is set to “1,”
there is reduced input bandwidth on the I
that pulses of less than 50 ns will not pass into the I
controller. This mode is recommended for noisy systems.
To control the various devices on the bus the following protocol
must be followed. First the master initiates a data transfer by
establishing a Start condition, defined by a high-to-low transi-
tion on SDA while SCL remains high. This indicates that an
address/data stream will follow. All peripherals respond to the
Start condition and shift the next eight bits (7-bit address + R/W
bit). The bits are transferred from MSB down to LSB. The periph-
eral that recognizes the transmitted address responds by pulling
the data line low during the ninth clock pulse. This is known
as an Acknowledge Bit. All other devices withdraw from the bus
at this point and maintain an idle condition. The idle condition
is where the device monitors the SDA and SCL lines waiting for
the Start condition and the correct transmitted address. The R/W
bit determines the direction of the data.
2
C Filter
0
2
C interface. For setting ALSB high, the input band-
1
2
LOAD
C lines is reduced and pulses of less than 50 ns
0
has a value of 300 Ω. For the outputs to con-
2
2
C filter allows significant noise reduction
C controller. Setting ALSB low allows
1
2
C lines.
0
SET
2
2
1
C-compatible) micro-
C lines, which allows
2
C lines, which means
must have a value
SET UP BY
ADDRESS
CONTROL
ALSB
A1
READ/WRITE
0
1
2
CONTROL
C internal
X
WRITE
READ