LTC4160-1 LINER [Linear Technology], LTC4160-1 Datasheet - Page 5

• Manufacturer Part Number: LTC4160-1
• Description: Switching Power Manager with USB On-The-Go And Overvoltage Protection
• Manufacturer: LINER [Linear Technology]

ELECTRICAL CHARACTERISTICS
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LTC4160E/LTC4160E-1 are guaranteed to meet performance
specifi cations from 0°C to 85°C. Specifi cations over the –40°C to 85°C
operating temperature range are assured by design, characterization and
correlation with statistical process controls.
Note 3: The LTC4160E/LTC4160E-1 include overtemperature protection
that is intended to protect the device during momentary overload
conditions. Junction temperature will exceed 125°C when overtemperature
protection is active. Continuous operation above the specifi ed maximum
operating junction temperature may impair device reliability.
TYPICAL PERFORMANCE CHARACTERISTICS
500
400
200
900
800
700
600
500
400
200
700
600
300
300
100
100
0
0
2.7
2.7
USB Limited Load Current vs Battery
Voltage (Battery Charger Disabled)
USB Limited Battery Charge
Current vs Battery Voltage
3.0
3.0
BATTERY VOLTAGE (V)
BATTERY VOLTAGE (V)
3.3
3.3
V
5x MODE
R
BUS
PROG
= 5V
= 1k
3.6
3.6
V
5x MODE
3.9
3.9
BUS
41601 G04
41601 G01
= 5V
4.2
4.2
160
140
120
100
100
140
120
80
40
60
80
40
20
60
20
0
0
2.7
2.7
USB Limited Load Current vs Battery
Voltage (Battery Charger Disabled)
USB Limited Battery Charge
Current vs Battery Voltage
V
1x MODE
R
BUS
PROG
= 5V
3.0
3.0
= 1k
BATTERY VOLTAGE (V)
BATTERY VOLTAGE (V)
3.3
3.3
Note 4: Total input current is the sum of quiescent current, I
measured current given by V
Note 5: The current limit features of this part are intended to protect the
IC from short term or intermittent fault conditions. Continuous operation
above the maximum specifi ed pin current rating may result in device
degradation or failure.
Note 6: The bidirectional switcher’s supply current is bootstrapped to
V
1/effi ciency. Total quiescent current is the sum of the current into the V
pin plus the refl ected current.
Note 7: h
with indicated PROG resistor.
BUS
3.6
3.6
and in the application will refl ect back to V
C/10
V
1x MODE
3.9
3.9
BUS
is expressed as a fraction of the measured full charge current
41601 G02
41601 G05
T
= 5V
A
= 25°C, unless otherwise noted.
4.2
4.2
LTC4160/LTC4160-1
1000
–250
–500
CLPROG
–250
–500
750
500
250
750
500
250
0
0
0
0
Battery and V
Load Current
Battery and V
vs Load Current
V
BAT = 3.8V
10x MODE
R
R
V
BAT = 3.8V
5x MODE
R
R
/R
BUS
BUS
CLPROG
PROG
CLPROG
PROG
CLPROG
250
= 5V
= 5V
200
= 2k
= 1k
= 3.01k
= 3.01k
LOAD CURRENT (mA)
LOAD CURRENT (mA)
500
• (h
V
OUT
400
BUS
BUS
BUS
BATTERY CURRENT
CLPROG
BATTERY CURRENT
by (V
(DISCHARGING)
750
CURRENT
V
Currents vs
(DISCHARGING)
Currents
BUS
BATTERY CURRENT
(CHARGING)
BATTERY CURRENT
(CHARGING)
600
+ 1).
BUS
CURRENT
1000
VBUSQ
/V
OUT
800
1250
, and
) •
41601 G06
41601 G03
41601f
5
OUT
1500
1000