LTC4223 LINER [Linear Technology], LTC4223 Datasheet - Page 12
![no-image](/images/no-image-200.jpg)
LTC4223
Manufacturer Part Number
LTC4223
Description
Dual Ideal Diode and Hot Swap Controller
Manufacturer
LINER [Linear Technology]
Datasheet
1.LTC4223.pdf
(24 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LTC4223CDHC-2#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC4223CDHD-1
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
LTC4223CDHD-2
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
LTC4223CGN-1
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
LTC4223CGN-2
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC4223CGN-2#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC4223IDHD-1
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC4223IGN-1
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTC4223IGN-1#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTC4223IGN-2#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
LTC4228-1/LTC4228-2
applicaTions inForMaTion
below OUT. If the input supply falls at a more modest rate,
the gate drive amplifier controls the MOSFET to maintain
OUT at 25mV below IN.
Board Presence Detect with EN
If ON is high when the EN pin goes low, indicating a board
presence, the LTC4228 initiates a 100ms timing cycle for
contact debounce. Upon board insertion, any bounces
on the EN pin restart the timing cycle. When the 100ms
timing cycle is done, the internal fault latches are cleared.
If the EN pin remains low at the end of the timing cycle,
HGATE is charged up with a 10µA current source to turn
on the Hot Swap MOSFET.
If the EN pin goes high, indicating a board removal, the
HGATE pin is pulled low with a 300µA current sink after
a 20µs delay, turning off the Hot Swap MOSFET without
clearing any latched faults.
Overcurrent Fault
The LTC4228 features an adjustable current limit with circuit
breaker function that protects the external MOSFETs against
short circuits or excessive load current. The voltage across
the external sense resistor (R
electronic circuit breaker (ECB) and active current limit
(ACL) amplifier. The electronic circuit breaker will turn off
the Hot Swap MOSFET with a 300µA current from HGATE
to GND if the voltage across the sense resistor exceeds
∆V
configured at the TMR pin.
Active current limiting begins when the sense voltage
exceeds the ACL threshold ∆V
is 1.3× the ECB threshold ∆V
Hot Swap MOSFET is brought under control by the ACL
amplifier and the output current is regulated to maintain
the ACL threshold across the sense resistor. At this point,
the fault filter starts the timeout with a 100µA current
charging the TMR pin capacitor. If the TMR pin voltage
exceeds its threshold (1.235V), the external MOSFET
turns off with HGATE pulled to ground by 300µA, and its
associated FAULT pulls low.
After the Hot Swap MOSFET turns off, the TMR pin ca-
pacitor is discharged with a 2µA pull-down current until
its threshold reaches 0.2V. This is followed by a cool-off
12
SENSE(CB)
(50mV) for longer than the fault filter delay
S1
SENSE(CB)
SENSE(ACL)
, R
S2
) is monitored by an
. The gate of the
(65mV), which
period of 14 timing cycles at the TMR pin. For the latch-off
part (LTC4228-1), the HGATE pin voltage does not restart
at the end of the cool-off period, unless the latched fault
is cleared by pulling the ON pin low or toggling the EN
pin from high to low. For the auto-retry part (LTC4228-2),
the latched fault is cleared automatically at the end of the
cool-off period, and the HGATE pin restarts charging up
to turn on the MOSFET. Figure 4 shows an overcurrent
fault on the 12V output.
In the event of a severe short-circuit fault on the 12V output
as shown in Figure 5, the output current can surge to tens
of amperes. The LTC4228 responds within 1µs to bring
the current under control by pulling the HGATE to OUT
voltage down to zero volts. Almost immediately, the gate
of the Hot Swap MOSFET recovers rapidly due to the R
and C
electronic circuit breaker times out. Due to parasitic sup-
ply lead inductance, an input supply without any bypass
capacitor may collapse during the high current surge
and then spike upwards when the current is interrupted.
Figure 11 shows the input supply transient suppressors
consisting of Z1, R
for the two supplies if there is no input capacitance.
10V/DIV
10V/DIV
40A/DIV
10V/DIV
10V/DIV
40A/DIV
HGATE
HGATE
HG
I
I
LOAD
LOAD
OUT
OUT
Figure 5. Severe Short-Circuit on 12V Output
network, and current is actively limited until the
Figure 4. Overcurrent Fault on 12V Output
SNUB1
, C
SNUB1
100µs/DIV
2µs/DIV
and Z2, R
SNUB2
422812 F04
422812 F05
, C
SNUB2
422812f
HG