AD7853BN AD [Analog Devices], AD7853BN Datasheet - Page 7
![no-image](/images/no-image-200.jpg)
AD7853BN
Manufacturer Part Number
AD7853BN
Description
3 V to 5 V Single Supply, 200 kSPS 12-Bit Sampling ADCs
Manufacturer
AD [Analog Devices]
Datasheet
1.AD7853BN.pdf
(34 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
REV. B
Pin
1
2
3
4
5
6, 12 AGND
7
8
9
10
11
13
14
15
16
17
18
19
20
21
22
23
24
Mnemonic
CONVST
BUSY
SLEEP
REF
REF
AV
C
C
AIN(+)
AIN(–)
NC
AMODE
POLARITY
SM1
SM2
CAL
DV
DGND
DOUT
DIN
CLKIN
SCLK
SYNC
REF1
REF2
DD
DD
IN
OUT
/
Analog Input. Negative input of the pseudo-differential analog input. Cannot go below AGND or above
Serial Clock Polarity. This pin determines the active edge of the serial clock (SCLK). Toggling this pin will
Description
Convert Start. Logic Input. A low to high transition on this input puts the track/hold into its hold mode and
starts conversion. When this input is not used, it should be tied to DV
Busy Output. The busy output is triggered high by the falling edge of CONVST or rising edge of CAL, and
remains high until conversion is completed. BUSY is also used to indicate when the AD7853/AD7853L has
completed its on-chip calibration sequence.
Sleep Input/Low Power Mode. A Logic 0 initiates a sleep and all circuitry is powered down including the
internal voltage reference provided there is no conversion or calibration being performed. Calibration data
is retained. A Logic 1 results in normal operation. See Power-Down section for more details.
Reference Input/Output. This pin is connected to the internal reference through a series resistor and is the
reference source for the analog-to-digital converter. The nominal reference voltage is 2.5 V and this appears
at the pin. This pin can be overdriven by an external reference or can be taken as high as AV
pin is tied to AV
tied to AV
Analog Positive Supply Voltage, +3.0 V to +5.5 V.
Analog Ground. Ground reference for track/hold, reference and DAC.
Reference Capacitor (0.1 F multilayer ceramic). This external capacitor is used as a charge source for the
internal DAC. The capacitor should be tied between the pin and AGND.
Reference Capacitor (0.01 F ceramic disc). This external capacitor is used in conjunction with the on-chip
reference. The capacitor should be tied between the pin and AGND.
Analog Input. Positive input of the pseudo-differential analog input. Cannot go below AGND or above
AV
AV
No Connect Pin.
Analog Mode Pin. This pin allows two different analog input ranges to be selected. A Logic 0 selects range
0 to V
AIN(–) cannot go below AGND. A Logic 1 selects range –V
–V
+V
reverse the active edge of the serial clock (SCLK). A Logic 1 means that the serial clock (SCLK) idles high
and a Logic 0 means that the serial clock (SCLK) idles low. It is best to refer to the timing diagrams and
Table IX for the SCLK active edges.
Serial Mode Select Pin. This pin is used in conjunction with the SM2 pin to give different modes of opera-
tion as described in Table X.
Serial Mode Select Pin. This pin is used in conjunction with the SM1 pin to give different modes of opera-
tion as described in Table X.
Calibration Input. This pin has an internal pull-up current source of 0.15 A. A Logic 0 on this pin resets
all calibration control logic and initiates a calibration on its rising edge. There is the option of connecting a
10 nF capacitor from this pin to DGND to allow for an automatic self-calibration on power-up. This input
overrides all other internal operations. If the autocalibration is not required, this pin should be tied to a
logic high.
Digital Supply Voltage, +3.0 V to +5.5 V.
Digital Ground. Ground reference point for digital circuitry.
Serial Data Output. The data output is supplied to this pin as a 16-bit serial word.
Serial Data Input. The data to be written is applied to this pin in serial form (16-bit word). This pin can act
as an input pin or as a I/O pin depending on the serial interface mode the part is in (see Table X).
Master Clock Signal for the device (4 MHz for AD7853, 1.8 MHz for AD7853L). Sets the conversion and
calibration times.
Serial Port Clock. Logic input/output. The SCLK pin is configured as an input or output, dependent on the
type of serial data transmission (self-clocking or external-clocking) that has been selected by the SM1 and
SM2 pins. The SCLK idles high or low depending on the state of the POLARITY pin.
This pin can be an input level triggered active low (similar to a chip select in one case and to a frame sync
in the other) or an output (similar to a frame sync) pin depending on SM1, SM2 (see Table X).
REF
REF
DD
DD
/2 to +V
REF
/2 to allow AIN(+) to go from 0 V to +V
at any time, and cannot go below AIN(–) when the unipolar input range is selected.
at any time.
(i.e., AIN(+) – AIN(–) = 0 to V
DD
.
REF
DD
/2). In this case AIN(+) cannot go below AGND so that AIN(–) needs to be biased to
, or when an externally applied reference approaches AV
PIN FUNCTION DESCRIPTIONS
–7–
REF
). In this case AIN(+) cannot go below AIN(–) and
REF
V.
REF
/2 to +V
DD
REF
.
/2 (i.e., AIN(+) – AIN(–) =
DD
AD7853/AD7853L
, the C
REF1
pin should also be
DD
. When this