MAX3202 MAXIM [Maxim Integrated Products], MAX3202 Datasheet - Page 2

• Manufacturer Part Number: MAX3202
• Manufacturer: MAXIM [Maxim Integrated Products]

ABSOLUTE MAXIMUM RATINGS
V
I/O_ to GND ................................................-0.3V to (V
Continuous Power Dissipation (T
Low-Capacitance, 2/3/4/6-Channel, ±15kV ESD
Protection Arrays for High-Speed Data Interfaces
Note 1: The UCSP devices are constructed using a unique set of packaging techniques that impose a limit on the thermal profile the
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
Note 2: Limits over temperature are guaranteed by design, not production tested.
Note 3: Idealized clamp voltages (L1 = L2 = L3 = 0) (Figure 1 ); see the Applications Information section for more information.
Note 4: Guaranteed by design. Not production tested.
2
Supply Voltage
Supply Current
Diode Forward Voltage
Channel Clamp Voltage
(Note 3)
Channel Leakage Current
Channel Input Capacitance
ESD PROTECTION
Human Body Model
IEC 61000-4-2
Contact Discharge
IEC 61000-4-2
Air-Gap Discharge
CC
2
3 × 2 UCSP (derate 3.4mW/°C above +70°C) ..............273mW
3 × 2 UCSP (derate 3.9mW/°C above +70°C) ..............308mW
3 × 3 UCSP (derate 4.7mW/°C above +70°C) ..............379mW
6-Pin Thin QFN (derate 24.4mW/°C above +70°C) ....1951mW
12-Pin Thin QFN (derate 16.9mW/°C above +70°C) ..1349mW
CC
× 2 UCSP (derate 3.0mW/°C above +70°C) ..............239mW
_______________________________________________________________________________________
to GND ...........................................................-0.3V to +7.0V
= +5V ±5%, T
PARAMETER
device can be exposed to during board-level solder attach and rework. This limit permits the use of only the solder profiles
recommended in the industry-standard specification, JEDEC 020A, paragraph 7.6, Table 3 for IR/VPR and Convection
Reflow. Preheating is required. Hand or wave soldering is not allowed.
A
= T
MIN
to T
SYMBOL
A
MAX
= +70°C)
V
I
V
CC
V
CC
C
, unless otherwise noted. Typical values are at V
F
I
T
Human Body Model,
I
T
Contact Discharge
(IEC 61000-4-2), I
T
Air-Gap Discharge
(IEC 61000-4-2), I
T
V
F
F
A
A
A
A
CC
= 10mA
= 10A
= +25°C, ±15kV
= +25°C, ±8kV
= +25°C, ±15kV
= 0°C to +50°C (Note 4)
= 5V, bias of V
CC
+ 0.3V)
F
F
CONDITIONS
= 24A
= 45A
CC
/2
Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Junction Temperature .....................................................+150°C
Bump Temperature (soldering) (Note 1)
Lead Temperature (soldering, 10s) .................................+300°C
Infrared (15s) ................................................................+220°C
Vapor Phase (60s) ........................................................+215°C
Positive transients
Negative transients
Positive transients
Negative transients
Positive transients
Negative transients
CC
= +5V and T
0.65
MIN
0.9
-1
A
= +25°C.) (Note 2)
TYP
±15
±15
1
5
±8
V
V
V
CC
CC
CC
MAX
-100
0.95
100
5.5
-25
-60
+1
7
+ 100
+ 25
+ 60
UNITS
nA
nA
pF
kV
kV
kV
V
V
V