CAT5411BI-10-TE13 CATALYST [Catalyst Semiconductor], CAT5411BI-10-TE13 Datasheet
![no-image](/images/no-image-200.jpg)
CAT5411BI-10-TE13
Related parts for CAT5411BI-10-TE13
CAT5411BI-10-TE13 Summary of contents
Page 1
The CAT5411 is two Digitally Programmable Potentiometers (DPPs™) integrated with control logic and 16 bytes of NVRAM memory. Each DPP consists of a series of 63 resistive elements connected between two externally accessible end points. The tap points between each ...
Page 2
C1 VCC ...
Page 3
The CAT5041 supports the SPI bus data transmission protocol. The synchronous Serial Peripheral Interface (SPI) helps the CAT5411 to interface directly with many of today's popular microcontrollers. The CAT5041 contains an 8-bit instruction register .The instruction set and the operation ...
Page 4
Temperature Under Bias .................. - +125 C Storage Temperature ........................ - +150 C Voltage on any Pin with (1)(2) Respect to V ................ -2. with Respect to Ground ................ -2.0V to +7.0V ...
Page 5
Over recommended operating conditions unless otherwise stated. I Power Supply Current CC I Standby Current ( Input Leakage Current LI I Output Leakage Current LO V Input Low Voltage IL V Input High Voltage IH V Output ...
Page 6
Over recommended operating conditions unless otherwise stated. t Data Setup Time SU t Data Hold Time H t SCK High Time WH t SCK Low Time WL f Clock Frequency SCK HOLD to Output Low (1) t ...
Page 7
Over recommended operating conditions unless otherwise stated. t Write Cycle Time WR Over recommended operating conditions unless otherwise stated. (1) N Endurance END (1) T Data Retention DR (1) V ESD Susceptibility ZAP (1)(2) I Latch-Up LTH Note: (1) This ...
Page 8
The first byte sent to the CAT5411 from the master/ processor is called the Device Address Byte. The most significant four bits of the Device Type address are a device type identifier. These bits for the CAT5411 are fixed at ...
Page 9
The CAT5411 contains two 6-bit Wiper Control Registers, one for each potentiometer. The Wiper Control Register output is decoded to select one of 64 switches along its resistor array. The contents of the WCR can be altered in four ways: ...
Page 10
The basic sequence of the three byte instructions is illustrated in Figure 8. These three-byte instructions exchange data between the WCR and one of the Data Registers. The WCR ...
Page 11
INC/DEC Command Issued SCK Voltage Out 11 t WRID High Voltage CS Write Cycle CS Document No. 2114, Rev. G ...
Page 12
Notes: (1) Any write or transfer to the Non-volatile Data Registers is followed by a high voltage cycle after CS goes high. Document No. 2114, Rev High Voltage CS Write Cycle High ...
Page 13
Prefix Device # CAT 5411 Optional Product Company ID Number Notes: (1) The device used in the above example is a CAT5411JI-10-TE13 (SOIC, Industrial Temperature, 10kohm, Tape & Reel) 0.5985 (15.20) 0.6141 (15.60) 0.050 (1.27) BSC 0.013 (0.33) 0.020 (0.51) ...
Page 14
PIN #1 INDENT. 1.1 MAX TYP -C- SEE DETAIL A Document No. 2114, Rev. F 4.4 + 0.1 -B- (1.78 TYP) 0.42 TYP 0 ALL LEAD TIPS LAND PATTERN RECOMMENDATION 0.1 ...
Page 15
Package Body Dimension X Package Body Dimension Y Package Height Package Body Thickness Ball Height Ball Diameter Total Ball Count Ball Count X Axis Ball Count Y Axis ...
Page 16
G Copyrights, Trademarks and Patents Trademarks and registered trademarks of Catalyst Semiconductor include each of the following: DPP ™ DPPs ™ ™ Catalyst Semiconductor has been issued U.S. and foreign patents and has patent applications pending that ...