TSA5514AT PHILIPS [NXP Semiconductors], TSA5514AT Datasheet
TSA5514AT
Available stocks
Related parts for TSA5514AT
TSA5514AT Summary of contents
Page 1
DATA SHEET TSA5514 1.3 GHz bidirectional I controlled synthesizer Product specification File under Integrated Circuits, IC02 INTEGRATED CIRCUITS 2 C-bus October 1992 ...
Page 2
... T IC storage temperature range stg ORDERING INFORMATION EXTENDED TYPE NUMBER PINS TSA5514 18 TSA5514T 16 TSA5514AT 20 Note 1. SOT102-1; 1996 December 4. 2. SOT109-1; 1996 December 4. 3. SOT 163-1; 1996 December 4. October 1992 2 C-bus controlled synthesizer APPLICATIONS TV tuners VCR Tuners DESCRIPTION The TSA5514 is a single chip PLL frequency synthesizer designed for TV tuning systems ...
Page 3
Philips Semiconductors 1.3 GHz bidirectional I synthesizer October 1992 2 C-bus controlled 3 Product specification TSA5514 ...
Page 4
Philips Semiconductors 1.3 GHz bidirectional I Fig.2 Pin configuration for SOT102. Fig.4 Pin configuration for SOT163. October 1992 2 C-bus controlled synthesizer 4 Product specification TSA5514 Fig.3 Pin configuration for SOT109. ...
Page 5
Philips Semiconductors 1.3 GHz bidirectional I PINNING PIN SYMBOL SOT102 SOT109 SOT163 n.c. SDA 4 4 SCL n. ...
Page 6
Philips Semiconductors 1.3 GHz bidirectional I FUNCTIONAL DESCRIPTION The TSA5514 is controlled via the two-wire I programming, there is one module address (7 bits) and the R/W bit for selecting READ or WRITE mode. WRITE mode: R (see ...
Page 7
Philips Semiconductors 1.3 GHz bidirectional I READ mode: R (see Table 2) Data can be read out of the TSA5514 by setting the R/W bit to 1. After the slave address has been recognized, the TSA5514 generates an ...
Page 8
Philips Semiconductors 1.3 GHz bidirectional I Table 3 ADC levels VOLTAGE APPLIED ON THE PORT 0.3 ...
Page 9
Philips Semiconductors 1.3 GHz bidirectional I CHARACTERISTICS unless otherwise specified cc amb All pin numbers refer to DIL18 version SYMBOL PARAMETER Functional range V supply voltage range cc T operating ambient amb ...
Page 10
Philips Semiconductors 1.3 GHz bidirectional I SYMBOL PARAMETER SCL and SDA inputs I HIGH level input current IH I LOW level input current IL Output SDA (pin 4; open collector) I output leakage current LO V output voltage O Charge-pump ...
Page 11
Philips Semiconductors 1.3 GHz bidirectional I synthesizer October 1992 2 C-bus controlled 11 Product specification TSA5514 ...
Page 12
Philips Semiconductors 1.3 GHz bidirectional I Fig.6 Prescaler typical input sensitivity curve; V Fig.7 Prescaler Smith chart of typical input impedance; V October 1992 2 C-bus controlled synthesizer = 4 Product specification TSA5514 = ...
Page 13
Philips Semiconductors 1.3 GHz bidirectional I FLOCK FLAG DEFINITION (FL) When the FL flag is 1, the maximum frequency deviation ( f) from stable frequency can be expressed as follows VCO O CP Where: ...
Page 14
Philips Semiconductors 1.3 GHz bidirectional I PACKAGE OUTLINES DIP18: plastic dual in-line package; 18 leads (300 mil pin 1 index 1 DIMENSIONS (inch dimensions are derived from the original mm dimensions UNIT ...
Page 15
Philips Semiconductors 1.3 GHz bidirectional I SO16: plastic small outline package; 16 leads; body width 3 pin 1 index 1 DIMENSIONS (inch dimensions are derived from the original mm dimensions) A UNIT ...
Page 16
Philips Semiconductors 1.3 GHz bidirectional I SO20: plastic small outline package; 20 leads; body width 7 pin 1 index 1 e DIMENSIONS (inch dimensions are derived from the original mm dimensions) A UNIT ...
Page 17
Philips Semiconductors 1.3 GHz bidirectional I synthesizer SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave ...
Page 18
Philips Semiconductors 1.3 GHz bidirectional I DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This ...