DP8572AMD/883 NSC [National Semiconductor], DP8572AMD/883 Datasheet
![no-image](/images/no-image-200.jpg)
DP8572AMD/883
Available stocks
Related parts for DP8572AMD/883
DP8572AMD/883 Summary of contents
Page 1
DP8572A DP8572AM Real Time Clock (RTC) General Description The DP8572A (8572AM militarized version) is intended for use in microprocessor based systems where information is required for multi-tasking data logging or general time of day date information This device is implemented ...
Page 2
Absolute Maximum Ratings Specifications for the 883 version of this product are listed separately Supply Voltage ( Input Voltage ( Output Voltage ( ...
Page 3
AC Electrical Characteristics PFAIL Symbol READ TIMING t Address Valid Prior to Read Strobe AR t Read Strobe Width (Note Chip Select to Data ...
Page 4
Military Version Absolute Maximum Ratings The 883 specifications are written to reflect the current (at the time of printing) Rel Electrical Test Specifica- tions (RETS) established by National Semiconductor for this product For a copy of the latest version ...
Page 5
Military Version AC Electrical Characteristics and PFAIL Symbol READ TIMING t Address Valid Prior to Read Strobe AR t Read Strobe Width (Note ...
Page 6
Timing Waveforms Read Timing Diagram Write Timing Diagram 9980 – 9980 – 4 ...
Page 7
General Description (Continued) The DP8572A’s interrupt structure provides three basic types of interrupts Periodic Alarm Compare and Power Fail Interrupt mask and status registers enable the masking and easy determination of each interrupt Pin Description (Inputs) These ...
Page 8
Functional Description The DP8572A contains a fast access real time clock inter- rupt control logic power fail detect logic and CMOS RAM All functions of the RTC are controlled by a set of seven registers A simplified block diagram that ...
Page 9
Functional Description (Continued) INITIAL POWER-ON of BOTH V and and V may be applied in any sequence In order for BB CC the power fail circuitry to function correctly whenever power is off the V pin ...
Page 10
Functional Description (Continued) The oscillator is programmed via the Real Time Mode Reg- ister to operate at various frequencies The crystal oscillator is designed to offer optimum performance at each frequen- cy Thus at 32 768 kHz the oscillator is ...
Page 11
Functional Description (Continued) Interrupts Fall Into Three Categories 1 The Alarm Compare Interrupt Issued when the value in the time compared RAM equals the counter 2 The Periodic Interrupts These are issued at every incre- ment of the specific clock ...
Page 12
Functional Description (Continued) 12 ...
Page 13
Functional Description (Continued) FIGURE 6 System-Battery Switchover (Upper Left) Power Fail If chip select is low when a power failure is detected a safety circuit will ensure that if a read or write is held active continuously for greater than ...
Page 14
Functional Description (Continued) the chip is unlocked but only after another 30 s min 63 s max debounce time The system designer must en- sure that his system is stable when power has returned The power fail circuitry contains active ...
Page 15
Functional Description (Continued) MAIN STATUS REGISTER The Main Status Register is always located at address 0 regardless of the register block or the page selected D0 This read only bit is a general interrupt status bit that is taken directly ...
Page 16
Functional Description (Continued) D5 The Delay Enable bit is used when a power fail occurs If this bit is set a 480 s delay is generated internally before the P interface is locked out This will enable the access the ...
Page 17
Functional Description (Continued) D7 This bit is used to program the signal appearing at the MFO output as follows D7 MFO Output Signal 0 Power Fail Interrupt 1 Buffered Crystal Oscillator INTERRUPT CONTROL REGISTER 0 D0 –D5 These bits are ...
Page 18
Control and Status Register Address Bit Map Main Status Register ADDRESS Page Register RAM Select Select Periodic Flag Register ...
Page 19
Application Hints Suggested Initialization Procedure for DP8572A in Battery Backed Applications that use the V Pin BB 1 Enter the test mode by writing bit D7 in the Period- ic Flag Register 2 Write zero to the ...
Page 20
Typical Performance Characteristics Operating Current vs Supply Voltage (Single Supply Mode F 32 768 kHz) e OSC Standby Current vs Power Supply Voltage (F 32 768 kHz) e OSC Operating Current vs Supply Voltage (Battery Backed Mode F 32 768 ...
Page 21
Physical Dimensions inches (millimeters) 24-Lead Hermetically Sealed Dual-In-Line Package (D) Order Number DP8572AMD 883 NS Package Number D24C Molded Dual-In-Line Package (N) Order Number DP8572AN NS Package Number N24C 21 ...
Page 22
Physical Dimensions inches (millimeters) (Continued) LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION As used herein 1 ...