MAX5042 MAXIM [Maxim Integrated Products], MAX5042 Datasheet
![no-image](/images/no-image-200.jpg)
MAX5042
Available stocks
Related parts for MAX5042
MAX5042 Summary of contents
Page 1
... ICs feature integrated switching power MOSFETs con- nected in a voltage-clamped, two-transistor, power-circuit configuration. These devices operate from a wide 20V to 76V input voltage range. The MAX5042 includes a hot- swap controller for use with an external power MOSFET to limit inrush current for applications where the power sup- ply is plugged into a live power backplane ...
Page 2
... Continuous Power Dissipation (T 56-Pin Thin QFN (derate 47.6mW/°C above +70°C) .......3.8W Junction to Ambient Thermal Resistance, θ Operating Temperature Range MAX5042ATN ................................................-40°C to +125°C MAX5043ETN ..................................................-40°C to +85°C Junction Temperature ......................................................+150°C Storage Temperature Range .............................-65°C to +150°C Lead Temperature (soldering, 10s) .................................+300°C ...
Page 3
Two-Switch Power ICs with Integrated Power MOSFETs and Hot-Swap Controller ELECTRICAL CHARACTERISTICS (V = 20V to 76V 18V, C POSINPWM REG15 0.22µ 10kΩ 0.22µF, V DRVDEL DRVDEL otherwise noted. Typical values are at V ...
Page 4
Two-Switch Power ICs with Integrated Power MOSFETs and Hot-Swap Controller ELECTRICAL CHARACTERISTICS (continued 20V to 76V 18V, C POSINPWM REG15 0.22µ 10kΩ 0.22µF, V DRVDEL DRVDEL otherwise noted. Typical values are at ...
Page 5
Two-Switch Power ICs with Integrated Power MOSFETs and Hot-Swap Controller ELECTRICAL CHARACTERISTICS (continued 20V to 76V 18V, C POSINPWM REG15 0.22µ 10kΩ 0.22µF, V DRVDEL DRVDEL otherwise noted. Typical values are at ...
Page 6
... PARAMETER SYMBOL DEN Hysteresis DEN Input Resistance SUPPLY CURRENT Supply Current Standby Supply Current HOT-SWAP CONTROLLER (MAX5042 Only) Hot-Swap UVLO Threshold Hot-Swap UVLO Hysteresis Hot-Swap UVLO Resistance Startup Delay HSEN Turn-Off Delay HSOK Output-High Leakage Current HSEN Reference Threshold ...
Page 7
... TEMPERATURE (°C) _______________________________________________________________________________________ Typical Operating Characteristics HOT-SWAP STARTUP DELAY vs. TEMPERATURE 175 170 165 160 155 150 125 -50 - TEMPERATURE (°C) MAX5042 toc04 32 V HSGATE 5V/div HSDRAIN 20V/div HSOK 27 20V/div 100kΩ PULLUP 26 OV ...
Page 8
Two-Switch Power ICs with Integrated Power MOSFETs and Hot-Swap Controller (V = 20V +25°C, unless otherwise noted.) POSINPWM A MAXIMUM DUTY CYCLE vs. TEMPERATURE MEASURED AT XFRMRL 46 -50 - ...
Page 9
Two-Switch Power ICs with Integrated Power MOSFETs and Hot-Swap Controller (V = 20V +25°C, unless otherwise noted.) POSINPWM A CURRENT-LIMIT THRESHOLD vs. TEMPERATURE 160 158 156 154 152 150 -50 - 100 TEMPERATURE (°C) ...
Page 10
... Source Connection for the Internal Low-Side Power MOSFET. Connect SRC to PWMPNEG with a low-value resistor for current limiting. Low-Side Connection for the Isolation Transformer Hot-Swap Controller Positive Input Supply (MAX5042 Only). Connect POSINHS along with POSINPWM to the most positive rail of the input supply. Pin Description ...
Page 11
... NEGIN provides the hot-swap circuit’s most negative connection. NEGIN is at the same potential as the IC substrate. Hot-Swap Gate (MAX5042 Only). Connect HSGATE to the gate of the external hot- swap MOSFET. Hot-Swap MOSFET Drain Sense (MAX5042 Only). Connect HSDRAIN to the drain of the external hot-swap MOSFET ...
Page 12
... QHS falls at a rate of approximately 10V/ms, drawing a current load from the backplane of approxi- mately 1A for each 100µ MAX5042’s PWM block is prevented from starting up until the QHS MOSFET is fully enhanced. After QHS completely turns on and the voltage across capacitor C ...
Page 13
... MAX5042/MAX5043 package. When REG15 is externally powered, the internal 15V regulator is disabled. Figures 3 and 4 show the block diagrams of the MAX5042 and MAX5043, respectively. The power-OK signals from the hot-swap section, regulators, thermal shutdown, and UVLO combine to generate the internal shutdown signal SHDN ...
Page 14
... CSS 7.5V 35 PWMNEG PWMNEG 13 PWMSD R Q UVLO S 32 CSOUT 25 POSINHS 840kΩ 27 HSEN 35kΩ NEGIN (29) Figure 3. Block Diagram of the MAX5042 Power IC 14 ______________________________________________________________________________________ REG15 OK OVT REG15 (15V) REG9 OK REG9 REF REG5 OK REF OK (9V) (1.25V) UVLO 7.5V "1" PWMNEG R LEADING- ...
Page 15
Two-Switch Power ICs with Integrated Power MOSFETs and Hot-Swap Controller MAX5043 41 REG15 39 REG5 REG5 (5V) REG5 OK 38 REG9 3 RCFF 5V IFLT 80µA OVRLD 11 FLTINT 2.3V/1.6V 4 RAMP CPWM 5 OPTO 5V 32µA 6 CSS 7.5V ...
Page 16
... R DRVDEL where t DRVDEL of PPWM to the switching of the internal power MOSFETs. The MAX5042/MAX5043 are multimode PWM power ICs supporting both voltage and current-mode control. Voltage-Mode Control and the PWM Ramp Soft-Start For voltage-mode control, the feed-forward PWM ramp is generated at RCFF. From RCFF connect a capacitor to PWMNEG and a resistor to POSINPWM ...
Page 17
... SP turns ratio. Current-Sense Amplifier and Current-Mode Control The MAX5042/MAX5043 can also be programmed for current-mode control (see Figure 6). This control method offers beneficial advantages for certain appli- cations. Current-mode control reduces the order of the output filter, allowing easier control-loop compensation. ...
Page 18
... The integration of thermal shutdown and the power MOSFETs result in a very robust power circuit. ) The MAX5042 integrates a PWM power IC with a hot- FLTINT swap controller. The design allows a power supply built around the MAX5042 to be safely hot-plugged into a live backplane without causing a glitch on the power- supply rail ...
Page 19
... R14 R20 C9 C12 10kΩ 10kΩ 220pF 0.1µF C20 0.1µF 100V NEGIN Figure 7. MAX5042 Typical Application Circuit (48V Power Supply with Hot-Swap Capability) ______________________________________________________________________________________ Table 1. MAX5042 Suggested External Hot-Swap MOSFETs MAXIMUM HSLR POSINPWM DRNH UVLO RAMP RCFF ...
Page 20
Two-Switch Power ICs with Integrated Power MOSFETs and Hot-Swap Controller V IN+ 32V TO 72V C1 R12 220µF 200kΩ 100V 1% R22 10kΩ R13 1MΩ C25 0.68µF C13 100V 1µF 0.22µF R14 R20 C9 C12 10kΩ 10kΩ 220pF 0.1µF PWMNEG ...
Page 21
... Two-Switch Power ICs with Integrated Power MOSFETs and Hot-Swap Controller TOP VIEW N.C. 1 N.C. 2 RCFF 3 RAMP 4 OPTO 5 CSS 6 BST 7 MAX5042ATN DRVIN 8 PWMPNEG 9 RCOSC 10 FLTINT 11 SYNC 12 PWMSD 13 N. THIN QFN EXPOSED PADDLE CONNECTED TO NEGIN. ...
Page 22
Two-Switch Power ICs with Integrated Power MOSFETs and Hot-Swap Controller (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information www.maxim-ic.com/packages.) Maxim cannot assume responsibility for use of ...