MAX5442 MAXIM [Maxim Integrated Products], MAX5442 Datasheet - Page 3

• Manufacturer Part Number: MAX5442
• Description: +3V/+5V, Serial-Input, Voltage-Output, 16-Bit DACs
• Manufacturer: MAXIM [Maxim Integrated Products]

ELECTRICAL CHARACTERISTICS (continued)
(V
unless otherwise noted. Typical values are at T
TIMING CHARACTERISTICS
(V
T
Note 1: Gain error tested at V
Note 2: R
Note 3: Min/max range guaranteed by gain-error test. Operation outside min/max limits will result in degraded performance.
Note 4: Reference input resistance is code-dependent, minimum at 8555hex in unipolar mode, 4555hex in bipolar mode.
Note 5: Slew-rate value is measured from 10% to 90%.
Note 6: Guaranteed by design. Not production tested.
Note 7: Guaranteed by power-supply rejection test and Timing Characteristics.
DYNAMIC PERFORMANCE—REFERENCE SECTION
STATIC PERFORMANCE—DIGITAL INPUTS
POWER SUPPLY
A
Reference -3dB Bandwidth
Reference Feedthrough
Signal-to-Noise Ratio
Reference Input Capacitance
Input High Voltage
Input Low Voltage
Input Current
Input Capacitance
Hysteresis Voltage
Positive Supply Range (Note 7)
Positive Supply Current
Power Dissipation
SCLK Frequency
SCLK Pulse Width High
SCLK Pulse Width Low
CS Low to SCLK High Setup
CS High to SCLK High Setup
SCLK High to CS Low Hold
SCLK High to CS High Hold
DIN to SCLK High Setup
DIN to SCLK High Hold
CLR Pulse Width Low
V
(power-up delay)
DD
DD
DD
= T
= +3V (MAX5443/MAX5444) or +5V (MAX5441/MAX5442), V
= +2.7V to +3.3V (MA5443/MAX5444) , V
High to CS Low
MIN
(MAX5441/ MAX5442).
PARAMETER
PARAMETER
OUT
to T
MAX
tolerance is typically ±20%.
, unless otherwise noted. Typical values are at T
_______________________________________________________________________________________
REF
= +2.0V, +2.5V, and +3.0V (MAX5443/MAX5444) or V
SYMBOL
SYMBOL
C
t
t
t
t
t
SNR
f
CSH0
CSH1
V
CSS0
CSS1
INREF
BW
C
I
t
t
CLW
V
PD
CLK
t
t
V
V
I
DD
CH
DH
CL
DS
IN
DD
IH
IL
IN
H
A
Code = FFFF hex
Code = 0000 hex, V
Code = 0000 hex
Code = FFFF hex
(Note 6)
MAX5443/MAX5444
MAX5441/MAX5442
All digital inputs at V
All digital inputs at
V
(Note 6)
DD
= +25°C.)
DD
= +4.5V to +5.5V (MAX5441/MAX5442), V
or GND
Voltage-Output, 16-Bit DACs
CONDITIONS
CONDITIONS
A
REF
REF
DD
= +25°C.) (Figure 1)
or GND
= 1V
= +2.5V, C
MAX5443/MAX5444
MAX5441/MAX5442
+3V/+5V, Serial-Input,
P-P
at 100kHz
L
= 10pF, GND = 0, R
REF
= +2.0V, +2.5V, +3.0V, and +5.5V
REF
MIN
MIN
2.4
2.7
4.5
20
20
15
15
35
20
15
20
= +2.5V, GND = 0, CMOS inputs,
0
L
TYP
0.15
0.12
0.36
0.60
TYP
170
92
70
20
= ∞, T
1
1
3
A
MAX
MAX
0.20
= T
0.8
3.6
5.5
±1
10
25
MIN
to T
UNITS
UNITS
mV
MHz
MHz
mW
mA
dB
pF
µA
pF
ns
ns
ns
ns
ns
ns
ns
ns
ns
µs
V
V
V
V
P-P
MAX
3
,