MAX6471 MAXIM [Maxim Integrated Products], MAX6471 Datasheet - Page 2

• Manufacturer Part Number: MAX6471
• Description: 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit
• Manufacturer: MAXIM [Maxim Integrated Products]

ABSOLUTE MAXIMUM RATINGS
(All voltages referenced to GND, unless otherwise noted.)
IN, SHDN, OUT, FB ..................................................-0.3V to +7V
MR, SET .......................................................-0.3V to (V
RESET (push-pull) ...................................-0.3V to (V
RESET (open drain)..................................................-0.3V to +7V
OUT Short Circuit .......................................................Continuous
Input/Output Current (all pins except IN and OUT) ............20mA
ELECTRICAL CHARACTERISTICS
(V
unless otherwise noted.) (Note 2)
300mA LDO Linear Regulators with Internal
Microprocessor Reset Circuit
Note 1: The MAX6477–MAX6484 are constructed using a unique set of packaging techniques that impose a limit on the thermal pro-
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Dual Mode is a trademark of Maxim Integrated Products, Inc.
2
Input Voltage Range
Input Undervoltage Lockout
Supply Current (Ground Current)
Shutdown Supply Current
REGULATOR CIRCUIT
Output Current
Output Voltage Accuracy (Fixed
Output Voltage Operation,
Table 1) MAX6469–MAX6476
Output Voltage Accuracy (Fixed
Output Voltage Operation,
Table 1) MAX6477–MAX6484
Adjustable Output Voltage Range
SET Reference Voltage
SET Dual Mode
SET Input Leakage Current
IN
_______________________________________________________________________________________
= (V
file the devices can be exposed to during board-level solder attach and rework. This limit permits only the use of the solder
profiles recommended in the industry-standard specification, JEDEC 020A, paragraph 7.6, Table 3 for IR/VPR and
Convection reflow. Pre-heating is required. Hand or wave soldering is not allowed.
OUT
PARAMETER
+ 0.5V) or +2.5V, whichever is greater, C
TM
Threshold
SYMBOL
V
I
SHDN
V
I
UVLO
V
SET
I
SET
Q
IN
V
I
I
T
1mA ≤ I
1mA ≤ I
1mA ≤ I
2mA ≤ I
2mA ≤ I
2mA ≤ I
(Note 3)
V
OUT
OUT
OUT
A
IN
SET
= +25°C
IN
falling
= 0
= 300mA
OUT
= 0, +1.2V (Note 3)
+ 0.3V)
+ 0.3V)
OUT
OUT
OUT
OUT
OUT
OUT
= 3.3µF, T
≤ 150mA, T
≤ 150mA, T
≤ 100mA, T
≤ 100mA, T
≤ 300mA, T
≤ 300mA, T
CONDITIONS
Continuous Power Dissipation (T
Operating Temperature Range ..........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
A
3 x 3 UCSP (derate 10.5mW/°C above +70°C) ............840mW
6-Pin SOT23 (derate 9.1mW/°C above +70°C).............727mW
8-Pin Thin QFN
(derate 24.4mW/°C above +70°C) ..............................1951mW
= -40°C to +85°C. Typical specifications are at T
A
A
A
A
A
A
= +25°C
= -40°C to +85°C
= +25°C
= -40°C to +85°C
= -40°C to +85°C
= -40°C to +85°C
1.200
V
2.25
MIN
300
-1.3
-2.3
-2.7
-1.1
-2.0
-2.5
2.5
SET
A
= +70°C)
1.229
TYP
185
±20
0.1
82
96
1.258
±100
MAX
+1.3
+2.3
+2.7
+1.1
+2.0
+2.5
2.47
136
5.5
5.0
1
A
= +25°C,
UNITS
mA
mV
µA
µA
nA
%
%
V
V
V
V