AD843J AD [Analog Devices], AD843J Datasheet - Page 11
![no-image](/images/no-image-200.jpg)
AD843J
Manufacturer Part Number
AD843J
Description
34 MHz, CBFET Fast Settling Op Amp
Manufacturer
AD [Analog Devices]
Datasheet
1.AD843J.pdf
(12 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD843JN
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD843JNZ
Manufacturer:
AD
Quantity:
1 000
Company:
Part Number:
AD843JNZ
Manufacturer:
TM
Quantity:
67 000
Part Number:
AD843JNZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD843JR
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD843JR-16
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD843JRZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
REV. D
MEASURING AD843 SETTLING TIME
Figure 28 shows the dynamic response of the AD843 while op-
erating in the settling time test circuit of Figure 27. The input of
the settling time fixture is driven by a flat-top pulse generator.
The error signal output from A1, the AD843 under test, is am-
plified by op amp A2 and then clamped by two high speed
Schottky diodes.
Figure 28. Settling Characteristics: +10 V to 0 V Step.
Upper Trace: Amplified Error Voltage (0.01%/Div)
Lower Trace: Output of AD843 Under Test (5 V/Div)
The error signal is clamped to prevent it from greatly overload-
ing the oscilloscope preamp. A Tektronix oscilloscope preamp
type 7A26 was chosen because it will recover from the approxi-
mately 0.4 volt overload, quickly enough to allow accurate mea-
surement of the AD843’s 135 ns settling time. Amplifier A2 is a
very high speed op amp; it provides a voltage gain of 10, provid-
ing a total gain of 5 from the error signal to the oscilloscope input.
A FAST PEAK DETECTOR CIRCUIT
The peak detector circuit of Figure 29, can accurately capture
the amplitude of input pulses as narrow as 200 ns and can hold
their value with a droop rate of less than 20 V/ s. This circuit
will capture the peak value of positive polarity waveforms; to
detect negative peaks, simply reverse the polarity of the two
diodes.
The high bandwidth and 200 V/ s slew rate of amplifier A2, an
AD843, allows the detector’s output to “keep up” with its input
thus minimizing overshoot. The low (<1 nA) input current of
the AD843 ensures that the droop rate is limited only by the
reverse leakage of diode D2, which is typically <10 nA for the
type shown. The low droop rate is apparent in Figure 30. The
Figure 29. A Fast Peak Detector Circuit
–11–
detector’s output (top trace) loses slightly over a volt of the
8 volt peak input value (bottom trace) in 75 ms, or a rate of
approximately 16 V/ s.
Amplifier A1, an AD847, can drive 680 pF hold capacitor, C
fast enough to “catch-up” with the next peak in 100 ns and still
settle to the new value in 250 ns, as illustrated in Figure 31.
Reducing the value of capacitor C
speed of this circuit at the expense of increased overshoot and
droop. Since the AD847 can drive an arbitrarily large value of
capacitance, C
of response time.
Figure 30. Peak Detector Response to 125 Hz Pulse Train
P
Figure 31. Peak Capture Time
can be increased to reduce droop, at the expense
P
to 100 pF will maximize the
AD843
P
,