DAC8412BTC/883 AD [Analog Devices], DAC8412BTC/883 Datasheet - Page 11
![no-image](/images/no-image-200.jpg)
DAC8412BTC/883
Manufacturer Part Number
DAC8412BTC/883
Description
Quad, 12-Bit DAC Voltage Output with Readback
Manufacturer
AD [Analog Devices]
Datasheet
1.DAC8412BTC883.pdf
(14 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DAC8412BTC/883
Manufacturer:
AMD
Quantity:
15
Company:
Part Number:
DAC8412BTC/883C
Manufacturer:
ADI
Quantity:
1 400
Part Number:
DAC8412BTC/883C
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
DAC8412BTC/883Q
Manufacturer:
AD
Quantity:
2
Reference Inputs
All four DACs share common reference high (V
ence low (V
inputs set the output high and low voltage limits of all four of
the DACs. Each reference input has voltage restrictions with
respect to the other reference and to the power supplies. The
V
and V
V
DAC8412 references cannot be inverted (i.e., V
greater than V
It is important to note that the DAC8412’s V
sinks and sources current. Also the input current of both V
and V
current sinking capability and must be buffered with an ampli-
fier to drive V
It is recommended that the reference inputs be bypassed with
0.2 µF capacitors when operating with ± 10 V references. This
limits the reference bandwidth.
Digital I/O
See Table I for digital control logic truth table. Digital I/O consists
of a 12-bit bidirectional data bus, two registers select inputs, A0
and A1, a R/W input, a RESET input, a Chip Select (CS), and
a Load DAC (LDAC) input. Control of the DACs and bus
direction is determined by these inputs as shown in Table I.
Digital data bits are labeled with the MSB defined as data bit
“11” and the LSB as data bit “0.” All digital pins are TTL/
CMOS compatible.
See Figure 35 for a simplified I/O logic diagram. The register
select inputs A0 and A1 select individual DAC registers “A”
(binary code 00) through “D” (binary code 11). Decoding of
the registers is enabled by the CS input. When CS is high no
decoding takes place, and neither the writing nor the reading of
the input registers is enabled. The loading of the second bank of
registers is controlled by the asynchronous LDAC input. By tak-
ing LDAC low while CS is enabled, all output registers can be
updated simultaneously. Note that the t
for updating all DACs is a minimum of 170 ns.
REV. D
A1
L
L
H
H
L
L
H
H
L
L
H
H
X
X
X
X
*DAC8412 resets to midscale, and DAC8413 resets to zero scale. L = Logic Low; H = Logic High; X - Don’t Care. Input and Output registers are transparent when
asserted.
REFL
REFL
REFH
REFL
can be set at any voltage between V
+ 2.5 V. Note that because of these restrictions the
A0
L
H
L
H
L
H
L
H
L
H
L
H
X
X
X
X
are code dependent. Many references have limited
can be set to any value between +V
REFL
REFH
REFH
) inputs. The voltages applied to these reference
. The V
).
R/W
L
L
L
L
L
L
L
L
H
H
H
H
X
X
X
X
REFL
CS
L
L
L
L
L
L
L
L
L
L
L
L
H
H
X
H
has no such special requirements.
RS
H
H
H
H
H
H
H
H
H
H
H
H
H
H
L
g
LDW
SS
and V
required pulsewidth
Table I. DAC8412/DAC8413 Logic Table
DD
REFH
REFL
REFH
REFH
– 2.5 V and
LDAC
L
L
L
L
H
H
H
H
H
H
H
H
L
H
X
X
) and refer-
cannot be
input both
– 2.5 V,
REFH
INPUT REG
WRITE
WRITE
WRITE
WRITE
WRITE
WRITE
WRITE
WRITE
READ
READ
READ
READ
HOLD
HOLD
*All registers reset to mid/zero-scale
*All registers latched to mid/zero-scale
–11–
The R/W input, when enabled by CS, controls the writing to and
reading from the input register.
Coding
Both the DAC8412 and DAC8413 use binary coding. The out-
put voltage can be calculated by:
where N is the digital code in decimal.
RESET
The RESET function can be used either at power-up or at any
time during the DAC’s operation. The RESET function is inde-
pendent of CS. This pin is active LOW and sets the DAC output
registers to either center code for the DAC8412, or zero code
for the DAC8413. The reset to center code is most useful when
the DAC is configured for bipolar references and an output of
zero volts after reset is desired.
Supplies
Supplies required are V
be set between –15 V and 0 V. V
erating range is between +5 V and +15 V.
V
function. It is normally connected to +5 V. This pin is a logic
reference input only. It does not supply current to the device.
If you are not using the readback function, V
circuit. While V
it does supply currents to the digital outputs when readback
is used.
Amplifiers
Unlike many voltage output DACs, the DAC8412 features buff-
ered voltage outputs. Each output is capable of both sourcing
and sinking 5 mA at ± 10 volts, eliminating the need for external
amplifiers when driving 500 pF or smaller capacitive load in
most applications. These amplifiers are short-circuit protected.
LOGIC
is the digital output supply voltage for the readback
V
OUT
OUTPUT REG
WRITE
WRITE
WRITE
WRITE
HOLD
HOLD
HOLD
HOLD
HOLD
HOLD
HOLD
HOLD
Update all output registers
HOLD
LOGIC
=
V
does not supply current to the DAC8412,
REFL
SS
, V
+
DD
(
V
DAC8412/DAC8413
REF H
and V
DD
MODE
Transparent
Transparent
Transparent
Transparent
WRITE INPUT
WRITE INPUT
WRITE INPUT
WRITE INPUT
READ INPUT
READ INPUT
READ INPUT
READ INPUT
HOLD
is the positive supply; its op-
_
4096
LOGIC
V
REFL
LOGIC
. The V
)
×
N
can be left open-
SS
supply can
DAC
A
B
C
D
A
B
C
D
A
B
C
D
All
All
All
All