ATAM893X-TKHYZ ATMEL [ATMEL Corporation], ATAM893X-TKHYZ Datasheet - Page 67
ATAM893X-TKHYZ
Manufacturer Part Number
ATAM893X-TKHYZ
Description
Flash Version for ATAR080, ATAR090/890 and ATAR092/892
Manufacturer
ATMEL [ATMEL Corporation]
Datasheet
1.ATAM893X-TKHYZ.pdf
(98 pages)
- Current page: 67 of 98
- Download datasheet (2Mb)
5.3.4.8
4680C–4BMCU–01/05
SSI Interrupt
Figure 5-44. MCL Bus Protocol 1
Bus not busy (1)
Start data transfer (2)
Stop data transfer (3)
Data valid (4)
Acknowledge
Figure 5-45. MCL Bus Protocol 2
The SSI interrupt INT3 can be generated either by an SSI buffer register status (i.e., transmit
buffer empty or receive buffer full), the end of SSI data telegram or on the falling edge of the
SC/SD pins on Port 4 (see P4CR). SSI interrupt selection is performed by the Interrupt Function
control bit (IFN). The SSI interrupt is usually used to synchronize the software control of the SSI
and inform the controller of the present SSI status. The Port 4 interrupts can be used together
with the SSI or, if the SSI itself is not required, as additional external interrupt sources. In either
case this interrupt is capable of waking the controller out of sleep mode.
To enable and select the SSI relevant interrupts use the SSI interrupt mask (SIM) and the Inter-
rupt Function (IFN) while the Port 4 interrupts are enabled by setting appropriate control bits in
P4CR register.
SC
SD
SC
SD
(1)
Start
condition
Start
(2)
1st Bit
1
Both data and clock lines remain HIGH.
A HIGH to LOW transition of the SD line while the clock (SC)
is HIGH defines a START condition.
A LOW to HIGH transition of the SD line while the clock (SC)
is HIGH defines a STOP condition.
The state of the data line represents valid data when,
after START condition, the data line is stable for the
duration of the HIGH period of the clock signal.
All address and data words are serially transmitted to and
from the device in eight-bit words. The receiving device
returns a zero on the data line during the ninth clock cycle to
acknowledge word receipt.
valid
Data
(4)
n
change
Data
8th Bit
8
valid
Data
(4)
ACK
9
ATAM893-D
condition
Stop
Stop
(3)
(1)
67
Related parts for ATAM893X-TKHYZ
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Atmel CryptoMemory
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
Atmel CryptoMemory
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
Atmel CryptoMemory, 16Kbit
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontrollers
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontroller with 64K/128K/256K Bytes In-System Programmable Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontroller with 16/32/64/128K Bytes In-System Programmable Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontroller with 16/32/64K Bytes In-System Programmable Programmable
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet: