DP83848K_08 NSC [National Semiconductor], DP83848K_08 Datasheet - Page 11
DP83848K_08
Manufacturer Part Number
DP83848K_08
Description
Manufacturer
NSC [National Semiconductor]
Datasheet
1.DP83848K_08.pdf
(78 pages)
- Current page: 11 of 78
- Download datasheet (2Mb)
1.4 LED INTERFACE
See Table 3 for LED Mode Selection.
1.5 RESET
1.6 STRAP OPTIONS
DP83848K uses many functional pins as strap options. The
values of these pins are sampled during reset and used to
strap the device into specific modes of operation. The strap
option pin assignments are defined below. The functional
pin name is indicated in parentheses.
LED_LINK
LED_SPEED
RESET_N
PHYAD0 (COL)
PHYAD1 (RXD_0)
PHYAD2 (RXD_1)
PHYAD3 (RXD_2)
PHYAD4 (RXD_3)
Signal Name
Signal Name
Signal Name
S, O, PU
S, O, PU
S, O, PU
S, O, PD
Type
Type
Type
I, PU
Pin #
Pin #
Pin #
22
21
23
35
36
37
38
39
LINK LED: In Mode 1, this pin indicates the status of the LINK.
The LED will be ON when Link is good.
LINK/ACT LED: In Mode 2, this pin indicates transmit and receive
activity in addition to the status of the Link. The LED will be ON
when Link is good. It will blink when the transmitter or receiver is
active.
SPEED LED: This LED is ON when DP83848K is in 100Mb/s and
OFF when DP83848K is in 10Mb/s. Functionality of this LED is in-
dependent of the mode selected.
RESET: Active Low input that initializes or re-initializes the
DP83848K. Asserting this pin low for at least 1 s will force a reset
process to occur. All internal registers will re-initialize to their de-
fault states as specified for each bit in the Register Block section.
All strap options are re-initialized as well.
PHY ADDRESS [4:0]: The DP83848K provides five PHY address
pins, the state of which are latched into the PHYCTRL register at
system Hardware-Reset.
The DP83848K supports PHY Address strapping values 0
(<00000>) through 31 (<11111>). A PHY Address of 0 puts the
part into the MII Isolate Mode. The MII isolate mode must be se-
lected by strapping Phy Address 0; changing to Address 0 by reg-
ister write will not put the Phy in the MII isolate mode. Please refer
to section 2.3 for additional information.
PHYAD0 pin has weak internal pull-up resistor.
PHYAD[4:1] pins have weak internal pull-down resistors.
11
A 2.2 k resistor should be used for pull-down or pull-up to
change the default strap option. If the default option is
required, then there is no need for external pull-up or pull
down resistors. Since these pins may have alternate func-
tions after reset is deasserted, they should not be con-
nected directly to VCC or GND.
Description
Description
Description
www.national.com
Related parts for DP83848K_08
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Thin SOT23 1A Load Step-Down DC-DC Regulator
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
TRI-STATE Dual Receiver
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Hex MOS Drivers
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Printer Solenoid Driver
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Quad High Current Peripheral Driver
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
(RS-422/RS-423) Line Drivers with TRI-STATE Outputs
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Multipoint RS485/RS422 Transceivers/Repeaters
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Low Power EIA-RS-485 Transceiver with Sleep Mode
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
BTL Handshake Transceiver
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Octal 80-Bit Static Shift Register
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
PUSH BUTTON PULSE DIALER CIRCUITS
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Hex Schmitt Trigger with Extended Input Voltage
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Microprocessor Real Time Clock
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Dual Line Receivers
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Dual TRI-STATE Differential Line Driver
Manufacturer:
NSC [National Semiconductor]
Datasheet: