AT89C51IC2-RLTIM ATMEL [ATMEL Corporation], AT89C51IC2-RLTIM Datasheet - Page 47
AT89C51IC2-RLTIM
Manufacturer Part Number
AT89C51IC2-RLTIM
Description
8-bit Flash Microcontroller with 2-wire Interface
Manufacturer
ATMEL [ATMEL Corporation]
Datasheet
1.AT89C51IC2-RLTIM.pdf
(147 pages)
- Current page: 47 of 147
- Download datasheet (2Mb)
Serial I/O Port
Framing Error Detection
4301C–8051–06/06
The serial I/O port in the AT89C51IC2 is compatible with the serial I/O port in the 80C52.
It provides both synchronous and asynchronous communication modes. It operates as a
Universal Asynchronous Receiver and Transmitter (UART) in three full-duplex modes
(Modes 1, 2 and 3). Asynchronous transmission and reception can occur simultaneously
and at different baud rates
Serial I/O port includes the following enhancements:
•
•
Framing bit error detection is provided for the three asynchronous modes (modes 1, 2
and 3). To enable the framing bit error detection feature, set SMOD0 bit in PCON regis-
ter (See Figure 17).
Figure 17. Framing Error Block Diagram
When this feature is enabled, the receiver checks each incoming data frame for a valid
stop bit. An invalid stop bit may result from noise on the serial lines or from simultaneous
transmission by two CPUs. If a valid stop bit is not found, the Framing Error bit (FE) in
SCON register (See Table 37.) bit is set.
Software may examine FE bit after each reception to check for data errors. Once set,
only software or a reset can clear FE bit. Subsequently received frames with valid stop
bits cannot clear FE bit. When FE feature is enabled, RI rises on stop bit instead of the
last data bit (See Figure 18. and Figure 19.).
Figure 18. UART Timings in Mode 1
Framing error detection
Automatic address recognition
SMOD0=X
SMOD0=1
SM0/FE
SMOD1
RXD
FE
RI
SMOD0
SM1
Start
bit
SM2
-
D0
REN
Set FE bit if stop bit is 0 (framing error) (SMOD0 = 1)
SM0 to UART mode control (SMOD0 = 0)
POF
To UART framing error control
D1
TB8
GF1
D2
RB8
GF0
D3
Data byte
D4
PD
TI
D5
IDL
RI
D6
SCON (98h)
PCON (87h)
D7
AT89C51IC2
Stop
bit
47
Related parts for AT89C51IC2-RLTIM
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
At89c51ic2 8-bit Flash Microcontroller With 2-wire Interface
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
IC MICRO CTRL 24MHZ 44TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC MICRO CTRL 24MHZ 44PLCC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC MICRO CTRL 24MHZ 44PLCC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC MICRO CTRL 24MHZ 40DIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC MICRO CTRL 24MHZ 40DIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
8-bit microcontroller with 4K bytes flash, 5V, 20MHz
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit microcontroller with 4K bytes flash, 5V, 20MHz
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
IC MICRO CTRL 24MHZ 44TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 4K 44TQFP
Manufacturer:
Atmel
Datasheet: