ADM485E AD [Analog Devices], ADM485E Datasheet - Page 13

• Manufacturer Part Number: ADM485E
• Manufacturer: AD [Analog Devices]

THEORY OF OPERATION
The ADM485E/ADM487E/ADM1487E are ruggedized RS-485
transceivers that operate from a single 5 V supply. They contain
protection against high levels of electrostatic discharge and are
ideally suited for operation in electrically harsh environments
or where cables can be plugged or unplugged. These devices are
intended for balanced data transmission and comply with TIA/
EIA standards RS-485 and RS-422. They contain a differential
line driver and a differential line receiver and are suitable for
half-duplex data transmission, as the driver and receiver share
the same differential pins.
The input impedance on the ADM485E is 12 kΩ, allowing up
to 32 transceivers on the differential bus. The ADM487E/
ADM1487E are 48 kΩ, allowing up to 128 transceivers on the
differential bus.
CIRCUIT DESCRIPTION
The ADM485E/ADM487E/ADM1487E are operated from
a single 5 V ± 10% power supply. Excessive power dissipation
caused by bus contention or output shorting is prevented by
a thermal shutdown circuit. If, during fault conditions, a sig-
nificant temperature increase is detected in the internal driver
circuitry, this feature forces the driver output into a high
impedance state.
The receiver contains a fail-safe feature that results in a logic
high output state if the inputs are unconnected (floating).
A high level of robustness is achieved using internal protection
circuitry, eliminating the need for external protection compo-
nents such as tranzorbs or surge suppressors.
Low electromagnetic emissions are achieved using slew-rate-
limited drivers, minimizing both conducted and radiated
interference.
The ADM485E/ADM487E/ADM1487E can transmit at data
rates up to 250 kbps.
A typical application for the ADM485E/ADM487E/ADM1487E
is illustrated in Figure 26, which shows a half-duplex link where
data can be transferred at rates up to 250 kbps. A terminating
resistor is shown at both ends of the link. This termination is
not critical, because the slew rate is controlled by the ADM485E/
ADM487E/ADM1487E and reflections are minimized.
The communications network can be extended to include
multipoint connections, as shown in Figure 29. As many as
32 ADM485E transceivers or 128 ADM487E/ADM1487E
transceivers can be connected to the bus.
Rev. 0 | Page 13 of 16
Table 7 and Table 8 show the truth tables for transmitting and
receiving.
Table 7. Transmitting Truth Table
RE
X
X
0
1
1
Table 8. Receiving Truth Table
RE
0
0
0
1
1
ESD Transient Protection Scheme
The ADM485E/ADM487E/ADM1487E use protective clamping
structures on their inputs and outputs that clamp the voltage to
a safe level and dissipate the energy present in ESD (electrostatic).
The protection structure achieves ESD protection up to ±15 kV
human body model (HBM).
X = don’t care.
X = don’t care.
1
1
RE
RO
ADM1487E
DE
DI
ADM485E/
ADM487E/
Receiving Inputs
V
GND
5V
Transmitting Inputs
CC
DE
1
1
0
0
Figure 26. Typical Half-Duplex Link Application
0.1µF
B
A
DE
0
0
0
0
ADM485E/ADM487E/ADM1487E
RS485/RS-422 LINK
DI
1
0
X
X
1
1
A to B
≥ +0.2 V
≤ −0.2 V
Inputs Open Circuit
X
1
B
0
1
High-Z
High-Z
Receiving Outputs
Transmitting Outputs
B
A
GND
ADM1487E
ADM485E/
ADM487E/
V
5V
CC
A
1
0
High-Z
High-Z
RO
1
0
1
High-Z
DE
RE
RO
DI
0.1µF