ATA6837_09 ATMEL [ATMEL Corporation], ATA6837_09 Datasheet
ATA6837_09
Related parts for ATA6837_09
ATA6837_09 Summary of contents
Page 1
Features • Six Half-bridge Outputs Formed by Six High-side and Six Low-side Drivers • Capable of Switching all Kinds of Loads (Such as DC Motors, Bulbs, Resistors, Capacitors and Inductors) • R Typically 1.0 at 25°C, Maximum 2.2 at 200°C ...
Page 2
Figure 1-1. Block Diagram QFN24 Input register Ouput register CLK INH Fault Detect Fault Detect 11 OUT1 ATA6837 ...
Page 3
Pin Configuration Figure 2-1. Pinning QFN 24, 5 Note: Table 2-1. Pin Description QFN24 Pin Symbol Function 1 OUT4 SENSE Only for testability in final test Half-bridge output 4; formed by internally connected power MOS high-side switch 4 and ...
Page 4
Table 2-1. Pin Description QFN24 (Continued) Pin Symbol Function Chip select input; 5V CMOS logic level input with internal pull up low = serial communication is enabled, high = disabled Serial clock input; 5V CMOS logic level input ...
Page 5
Functional Description 3.1 Serial Interface Data transfer starts with the falling edge of the CS signal. Data must appear at DI synchronized to CLK and is accepted on the falling edge of the CLK signal. LSB (bit 0, SRR) ...
Page 6
Table 3-2. Bit Note: Table 3-3. Status of the Input Register After Power on Reset Bit 15 Bit 14 Bit 13 Bit 12 Bit ...
Page 7
Power-supply Fail In case of undervoltage at pin VS, an internal timer is started. When during a permanent under- voltage the delay time (t set and all outputs are disabled. When normal voltage is present again, the outputs are ...
Page 8
Absolute Maximum Ratings Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated ...
Page 9
Electrical Characteristics 7.5V < V < 40V; 4.75V < V < 5.25V; INH = High; –40°C < pins. No. Parameters Test Conditions 1 Current Consumption V V Total quiescent current V 1.1 (V and all outputs ...
Page 10
Electrical Characteristics (Continued) 7.5V < V < 40V; 4.75V < V < 5.25V; INH = High; –40°C < pins. No. Parameters Test Conditions Thermal shutdown 4.6 hysteresis Ratio thermal 4.7 shutdown/thermal prewarning Ratio thermal 4.8 shutdown/thermal ...
Page 11
Electrical Characteristics (Continued) 7.5V < V < 40V; 4.75V < V < 5.25V; INH = High; –40°C < pins. No. Parameters Test Conditions Low-side open load Input register bit 13 5.13 detection current (OLD) = low, ...
Page 12
Electrical Characteristics (Continued) 7.5V < V < 40V; 4.75V < V < 5.25V; INH = High; –40°C < pins. No. Parameters Test Conditions 8 Serial Interface: Logic Output DO 8.1 Output voltage low level I OL ...
Page 13
Figure 8-1. Serial Interface Timing Diagram with Chart Numbers CLK 3 DI CLK DO Inputs DI, CLK, CS: High level = 0.7 Output DO: High level = 0.8 4953E–AUTO–09/ ...
Page 14
Noise and Surge Immunity Parameters Conducted interferences Interference suppression ESD (Human Body Model) CDM (Charge Device Model) MM (Machine Model) Note: 1. Test pulse 40V vbmax 10. Application Circuit Figure 10-1. Application Circuit VCC S I ...
Page 15
Application Notes • Connect the blocking capacitors at V GND pins. • Recommended value for capacitors at V Electrolytic capacitor C > 22 µF in parallel with a ceramic capacitor C = 100 nF. Value for electrolytic capacitor depends ...
Page 16
Ordering Information Extended Type Number ATA6837-PXQW 12. Package Information Package: QFN Exposed pad 3.6 x 3.6 (acc. JEDEC OUTLINE No. MO-220) Dimensions in mm Not indicated tolerances ±0. Drawing-No.: 6.543-5122.01-4 Issue: ...
Page 17
Revision History Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. 4953E-AUTO-09/09 4953D-AUTO-10/08 4953C-AUTO-09/07 4953B-AUTO-07/07 4953E–AUTO–09/09 History Section 7 “Electrical Characteristics” number 1.7 on ...
Page 18
Headquarters Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to ...