MAX2361 MAXIM [Maxim Integrated Products], MAX2361 Datasheet - Page 6

• Manufacturer Part Number: MAX2361
• Description: Evaluation Kits
• Manufacturer: MAXIM [Maxim Integrated Products]

The MAX2361/MAX2363W EV kits are fully assembled
and factory tested. Follow the instructions in the
Connections and Setup section.
This section lists the recommended test equipment to
• One TCXO (Temperature-Components Crystal
• An RF spectrum analyzer with optional digital modu-
• A power supply that can provide 250mA at +3.3V
• A power supply that can provide 50mA at +5V
• An additional voltage source for control of VGA func-
• I/Q arbitrary waveform generator or CDMA generator
verify the operation of the MAX2361/MAX2363/
MAX2365. It is intended as a guide only, and substitu-
tions may be possible.
MAX2361/MAX2363W Evaluation Kits
Note: Please indicate that you are using the MAX2361/
MAX2363W when contacting these component suppliers.
Win95
Microsoft Corp.
6
Alpha Industries
AVX
Coilcraft
Murata
Taiyo Yuden
Toko
DESIGNATION
Oscillator) at 19.68MHz for the PLL reference fre-
quency
lation personality (Rohde & Schwarz FSEA30 or
equivalent)
tions
_______________________________________________________________________________________
SUPPLIER
®
None
None
None
None
None
/98
®
, Win2000
MAX2363W Component List
QTY
®
7
1
1
1
1
, WinNT
Component Suppliers
617-935-5150
803-946-0690
847-639-6400
770-436-1300
408-573-4150
708-297-0070
Test Equipment Required
PHONE
Shunts for JU1, JU3, JU6–JU10
MAX2361/MAX2363/MAX2365
data sheet
INTF2300 board
Shunt for JU2
Ribbon cable
®
are registered trademarks of
DESCRIPTION
Quick Start
(continued)
617-933-2359
803-626-3123
847-639-1469
770-436-3030
408-573-4159
708-699-1194
FAX
• PC (486DX33 or better) with Win95
• INTF2300 interface board (supplied with EV kit)
This section provides step-by-step instructions for get-
ting the EV kit up and running in cellular and PCS
CDMA modes.
Perform the following steps to evaluate the MAX2361 in
the cellular CDMA mode:
1) Verify shunts JU1, JU2, and JU6–JU10 are in place.
2) Connect the INTF2300 interface cable as shown in
3) Connect a +3.0V power supply to VBAT. The
4) Connect a +5.0V power supply to the header labeled
5) Connect the TCXO to the REF port.
6) Connect a CDMA baseband signal generator to the
7) Install and run Maxim CDMA control software.
8) With the MAX236X control screen active, set the reg-
9) Click on the Send Data button for each of the con-
10) Apply 2.4V to GC via JU4.
11) Connect RFL to the spectrum analyzer. Configure
12) The output power should be about +9dBm after
(Agilent E4433B or equivalent)
WinNT
able parallel port
Figure 8. Note: Pin 1 of the interface cable corre-
sponds to the red wire. Pin 1 is designated in
silkscreen on each of the PC boards.
INTF2300 board derives its power from the MAX2361
EV kit.
“+5V”.
I and Q ports using BNC connectors. Set the modu-
lation to reverse-channel CDMA
Software is also available on the web at
www.maxim-ic.com. On the IC selection form, click
on the MAX236X control button. Select P4. Click on
register views.
isters according to Table 1.
trol registers located at the right of the screen.
There are eight registers that need to be down-
loaded to the IC. The Lock indicator on the screen
(and on the EV board) should be red, indicating
lock.
the spectrum analyzer to measure ACPR for
reverse-channel CDMA. Set the center frequency to
836MHz with a +10dBm reference level.
accounting for cable and connector loss. The ACPR
at ±885kHz offset should be -54dBc, and the ACPR
at ±1.98MHz offset should be -65dBc.
®
4.0 or later operating system and an avail-
Connections and Setup
Cellular CDMA Mode
®
/98
®
, Win2000
®
,