M-8870-02P ETC2 [List of Unclassifed Manufacturers], M-8870-02P Datasheet - Page 3

• Manufacturer Part Number: M-8870-02P
• Description: DTMF Receiver
• Manufacturer: ETC2 [List of Unclassifed Manufacturers]

Guard time adjustment also allows the designer to tailor system
parameters such as talkoff and noise immunity. Increasing t
improves talkoff performance, since it reduces the probability
that tones simulated by speech will maintain signal condition
long enough to be registered. On the other hand, a relatively
short t
noisy environments where fast acquisition time and immunity to
dropouts would be required. Design information for guard time
adjustment is shown in Figure 5.
Teltone Corporation, 22121-20th Avenue SE, Bothell, WA 98021-4408 U.S.A
40-406-00011, Rev. E
11 - 14 Q1, Q2,
Pin
10
15
16
17
18
* -02 only. Connect to V
1
2
3
4
5
6
7
8
9
REC
Q3, Q4
Name
OSC1
OSC2
St/GT
with a long t
V
INH*
V
PD*
V
StD
IN+
ESt
IN-
GS
OE
REF
SS
DD
Figure 5 Guard Time Adjustment
Non-inverting input
Inverting input
Gain select. Gives access to output of front-end amplifier for connection of feedback resistor.
Reference voltage output (nominally V
Inhibits detection of tones representing keys A, B, C, and D.
Power down. Logic high powers down the device and inhibits the oscillator. Internal pulldown.
Clock input
Clock output
Negative power supply (normally connected to 0 V).
Tri-statable output enable (input). Logic high enables the outputs Q1 - Q4. Internal pullup.
Tri-statable data outputs. When enabled by OE, provides the code corresponding to the last valid tone pair received (see
Table 5).
Delayed steering output. Presents a logic high when a received tone pair has been registered and the output latch is up-
dated. Returns to logic low when the voltage on St/GT falls below V
Early steering output. Presents a logic high immediately when the digital algorithm detects a recognizable tone pair (sig-
nal condition). Any momentary loss of signal condition will cause ESt to return to a logic low.
Steering input/guard time output (bidirectional). A voltage greater than V
the detected tone pair and update the output latch. A voltage less than V
The GT output acts to reset the external steering time constant, and its state is a function of ESt and the voltage on St.
(See Figure 7).
Positive power supply. (Normally connected to +5V.)
DO
SS
would be appropriate for extremely
for -01 version
Connections to the front-end differential amplifier.
3.579545 MHz crystal connected between these pins completes the internal oscillator.
Table 1 Pin Functions
DD
/2). May be used to bias the inputs at mid-rail.
REC
Page 3
M-8870
Power-down and Inhibit Mode ( -02 only)
A logic high applied to pin 6 (PD) will place the device into
standby mode to minimize power consumption. It stops the os-
cillator and the functioning of the filters. On the M-8870-01 mod-
els, this pin is tied to ground (logic low).
Inhibit mode is enabled by a logic high input to pin 5 (INH). It in-
hibits the detection of 1633 Hz. The output code will remain the
same as the previous detected code (see Table 1). On the
M-8870-01 models, this pin is tied to ground (logic low).
Input Configuration
The input arrangement of the M-8870 provides a differential in-
put operational amplifier as well as a bias source (V
the inputs at mid-rail. Provision is made for connection of a feed-
back resistor to the op-amp output (GS) for gain adjustment.
In a single-ended configuration, the input pins are connected as
shown in Figure 4 with the op-amp connected for unity gain and
V
configuration, which permits gain adjustment with the feedback
resistor R
DTMF Clock Circuit
The internal clock circuit is completed with the addition of a stan-
dard 3.579545 MHz television color burst crystal. The crystal
can be connected to a single M-8870 as shown in Figure 4, or to
a series of M-8870s. As illustrated in Figure 7, a single crystal
can be used to connect a series of M-8870s by coupling the os-
cillator output of each M-8870 through a 30 pF capacitor to the
oscillator input of the next M-8870.
Description
REF
biasing the input at 1/2V
5
.
TSt
Phone: [phone] or 425-487-1515 Fax: [phone]
.
TSt
TSt
detected at St causes the device to register
E-mail: [e-mail] Internet: www.teltone.com
frees the device to accept a new tone pair.
DD
. Figure 6 shows the differential
REF
) to bias