ADL5201-EVALZ AD [Analog Devices], ADL5201-EVALZ Datasheet - Page 15
![no-image](/images/no-image-200.jpg)
ADL5201-EVALZ
Manufacturer Part Number
ADL5201-EVALZ
Description
Wide Dynamic Range, High Speed
Manufacturer
AD [Analog Devices]
Datasheet
1.ADL5201-EVALZ.pdf
(28 pages)
Data Sheet
THEORY OF OPERATION
DIGITAL INTERFACE OVERVIEW
The
parallel control interface, serial peripheral interface, and gain
up/down interface. The desired gain control option is selected via
two control pins, MODE0 and MODE1 (see Table 4 for the
truth table for the mode control pins). The gain code is in 6-bit
binary format. A voltage from 1.4 V to 3.3 V is required for a
logic high.
Two pins are common to all gain control options: PM and PWUP.
PM allows the user to choose operation in low power mode or
high performance mode. PWUP is the power-up pin. Physical
pins are shared among the three interfaces, resulting in as many
as three different functions per digital pin (see Table 3).
Table 4. Digital Control Interface Selection Truth Table
MODE1
0
0
1
1
PARALLEL DIGITAL INTERFACE
The parallel digital interface uses six binary bits (Bits[A5:A0])
and a latch pin (LATCH). The Latch pin controls whether the
input data latch is transparent or latched. In transparent mode,
the gain changes as the input gain control bits change. In latched
mode, gain is determined by the latched gain setting and does
not change with the input gain control bits.
SERIAL PERIPHERAL INTERFACE (SPI)
The SPI uses three pins: SDIO, SCLK, and CS . The SPI data
register consists of two bytes: six gain control bits, two attenu-
ation step size address bits, one read/write bit, and seven don’t
care bits. SDIO is the serial data input and output pin. The
SCLK pin is the serial clock, and CS is the channel select pin.
DATA
ADL5201
D0
D1
DVGA has three digital gain control options:
D2
MODE0
0
1
0
1
D3
Figure 49. 16-Bit SPI Register
D4
MSB LSB MSB
D5
FA0
FA1
R/W DNC DNC DNC DNC DNC DNC DNC
FAST ATTACK ATTENUATION
STEP SIZE ADDRESS
GAIN CONTROL
Interface
Parallel control
Serial peripheral (SPI)
Up/down
Up/down
DO NOT CARE
(7 BITS)
READ/WRITE
Rev. 0 | Page 15 of 28
To write to the SPI register, CS must be pulled low and 16 clock
pulses must be applied to SCLK. To read the SPI register value,
the R/W bit must be set high, CS must be pulled low, and the
part must be clocked. After the register is read out during the
next 16 clock cycles, the SPI is automatically placed in write mode.
Fast Attack
The fast attack feature, accessible via the SPI, allows the gain to
be reduced from its present gain setting by a predetermined step
size. Four different attenuation step sizes are available. The
truth table for fast attack is shown in Table 5.
Table 5. SPI 2-Bit Attenuation Step Size Truth Table
FA1
0
0
1
1
SPI fast attack mode is controlled by the FA pin. A logic high
on the FA pin results in an attenuation that is selected by
Bits[FA1:FA0] in the SPI register.
UP/DOWN INTERFACE
The GS1 and GS0 pins control the up/down gain step function.
Gain is increased by a clock pulse on the UPDN_CLK pin
(rising and falling edges) when the UPDN_DAT pin is high.
Gain is decreased by a clock pulse on the UPDN_CLK pin
when the UPDN_DAT pin is low.
Reset is detected by a rising edge latching data having one polarity,
with the falling edge latching the opposite polarity. Reset results
in a minimum binary gain code of 111111.
The truth table for the gain step function is shown in Table 6.
The step size is selectable using the GS1 and GS0 pins. The gain
is limited by the top and bottom of the control range.
Table 6. Gain Step Size Control Truth Table
GS1
0
0
1
1
UPDN_DAT
UPDN_CLK
UP
Figure 50. Up/Down Timing
FA0
0
1
0
1
GS0
0
1
0
1
DN
RESET
Step Size (dB)
2
4
8
16
Step Size (dB)
0.5
1
2
4
ADL5201