ADL5360-EVALZ AD [Analog Devices], ADL5360-EVALZ Datasheet
ADL5360-EVALZ
Related parts for ADL5360-EVALZ
ADL5360-EVALZ Summary of contents
Page 1
... IIP3 version of the dual mixer without the IF amplifiers, please contact the factory). The ADL5360 provides two switched LO paths that can be utilized in TDD applications where it is desirable to rapidly alternate between two local oscillators. LO current can be externally set using a resistor to minimize DC current REV ...
Page 2
... ADL5360 ADL5360—Specifications at V Table 25° 900 MHz Parameter RF INPUT INTERFACE Return Loss Input Impedance RF Frequency Range OUTPUT INTERFACE Output Impedance IF Frequency Range 1 DC Bias Voltage LO INTERFACE LO Power Return Loss Input Impedance LO Frequency Range DYNAMIC PERFORMANCE ...
Page 3
... Preliminary Technical Data ADL5360—Specifications at VS=3.3v Table 3 25° 900 MHz Parameter DYNAMIC PERFORMANCE Power Conversion Gain Voltage Conversion Gain SSB Noise Figure Input Third Order Intercept Input Second Order Intercept Input 1 dB Compression Point POWER INTERFACE Supply Voltage Quiescent Current = 703 MHz, LO power = 0 dBm 50Ω ...
Page 4
... ADL5360 ABSOLUTE MAXIMUM RATINGS Table 2. Parameter Supply Voltage, V POS PWDN, LOSW, VGS0, VGS1, VGS2 RF Input Power, DVIN, MNIN Internal Power Dissipation θ (Exposed Paddle Soldered Down) JA θ (At Exposed Paddle) JC Maximum Junction Temperature Operating Temperature Range Storage Temperature Range Stresses above those listed under Absolute Maximum Ratings Rating may cause permanent damage to the device ...
Page 5
... Main Channel External Inductor. Connect 10nH inductor to ground for typical operation. 32, 33 MNOP, MNON Main Channel Differential Open-Collector Outputs. MNOP and MNON should be pulled-up to VCC using pull- up choke inductors. 35 MNGM Main Amplifier Bias Setting. Connect 1.2kΩ resistor to ground for typical operation. Figure 2. Pin Configuration REV. PrA | Page ADL5360 ...
Page 6
... ADL5360 TYPICAL PERFORMANCE CHARACTERISTICS– 25°C, as measured using typical circuit schematic with low-side LO unless otherwise noted Figure 3. Conversion Gain versus RF Frequency Figure 4. IIP3 versus RF Frequency Figure 5. IP1dB versus RF Frequency Preliminary Technical Data PRELIMINARY DATA Figure 6. Single-Sideband NF versus RF Frequency Figure 7 ...
Page 7
... Preliminary Technical Data EVALUATION BOARD SCHEMATIC Figure 9. Evaluation Board Schematic. REV. PrA | Page ADL5360 ...
Page 8
... ADL5360 Table 3. Eval Board Configuration Components Function C1, C4, C5, C8, C10, C12, Power Supply Decoupling. Nominal supply decoupling consists a C13, C15, C18, C21, C22, 0.01 μF capacitor to ground in parallel with 10pF capacitors to C23, C24, C25, C26 ground positioned as close to the device as possible. Z1-Z4, C2, C3, C6, C7, C9, RF Main and Diversity Input Interface ...
Page 9
... Temperature Models Range ADL5360XCPZ-R7 −40°C to +85°C ADL5360XCPZ-WP −40°C to +85°C ADL5360-EVALZ Figure 10. 36-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 6mm × Body, Very Thin Quad (CP-36-1)) Dimensions shown in millimeters Package Description 36-Lead Lead Frame Chip Scale Package [LFCSP_VQ] ...