PI3C3861L PERICOM [Pericom Semiconductor Corporation], PI3C3861L Datasheet - Page 2

• Manufacturer Part Number: PI3C3861L
• Description: 2.5V/3.3V, High Bandwidth, Hot Insertion, 10-Bit, 2-Port, BusSwitch
• Manufacturer: PERICOM [Pericom Semiconductor Corporation]

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Capacitance
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined
5. This parameter is determined by device characterization but is not production tested.
DC Electrical Characteristics
Parameters Description
Parameters
Storage Temperature .......................................................... –65°C to +150°C
Ambient Temperature with Power Applied ............................. –40°C to +85°C
Supply Voltage to Ground Potential (Inputs & Vcc Only) ........ –0.5V to +4.6V
Supply Voltage to Ground Potential (Outputs & D/O Only) ..... –0.5V to +4.6V
DC Input Voltage .................................................................... –0.5V to +5.5V
DC Output Current ..............................................................................120mA
Power Dissipation .................................................................................. 0.5W
C
C
C
by the lower of the voltages on the two (A,B) pins.
V
V
I
I
I
V
R
IH
IL
OZH
IN
OFF
ON
ON
IH
IL
IK
(5)
Input HIGH Voltage
Input LOW Voltage
Input HIGH Current
Input LOW Current
High Impedance Output Current 0
Clamp Diode Voltage
Switch On Resistance
(T
A
Description
Input Capacitance
A/B Capacitance, Switch Off
A/B Capacitance, Switch On
= 25°C, f = 1 MHz)
CC
= 3.3V, T
(4)
(Over Operating Range, T
A
= 25°C ambient and maximum loading.
Guaranteed Logic HIGH Level
Guaranteed Logic LOW Level
V
V
V
V
V
CC
CC
CC
CC
CC
A, B V
= Max., V
= Max., V
= Min., V
= Min., V
= Min., I
Test Conditions
CC
IN
IN
IN
IN
IN
A
= –18mA
= 2.4V, I
= 0.0V, I
2
= –40°C to +85°C, V
= V
= GND
Test Conditions
V
V
V
CC
IN
IN
IN
(1)
= 0V
= 0V
= 0V
ON
ON
= 48mA
= 15mA
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the device.
This is a stress rating only and functional operation
of the device at these or any other conditions above
those indicated in the operational sections of this
specification is not implied. Exposure to absolute maxi-
mum rating conditions for extended periods may affect
reliability.
Hot-Insertion, 10 -Bit, 2-Port, Bus Switch
CC
= 3.3V ±10%)
Min.
–0.5
2.0
2.5V/3.3V, High-Bandwidth,
–0.73
Typ
Typ
10.0
3.5
5.0
5
8
(2)
Units
pF
Max.
– 1.2
PS8198C
0.8
±1
±1
±1
15
7
PI3C3861
Units
µA
02/11/03
V
V