AT24C32C ATMEL [ATMEL Corporation], AT24C32C Datasheet

Page 1

... The device’s cascadable feature allows devices to share a common 2- wire bus. The device is optimized for use in many industrial and commercial applica- tions where low power and low voltage operation are essential. The AT24C32C/64C is available in space saving 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead TSSOP, 8-lead Ultra Thin Mini-MAP (MLP2x3) and, 8-ball dBGA2 packages and is accessed via a 2- wire serial interface ...

Page 2

Absolute Maximum Ratings* Operating Temperature...................................... -55 to +125°C Storage Temperature ......................................... -65 to +150°C Voltage on Any Pin with Respect to Ground ....................................... -1.0 to +5.0V Maximum Operating Voltage ............................................ 4.3V DC Output Current........................................................ 5.0 mA Block Diagram 5174B–SEEPR–12/06 *NOTICE: ...

Page 3

... If the pin is left floating, the WP pin will be internally pulled down to GND if the capacitive coupling to the circuit board V >3pF, Atmel recommends connecting the pin to GND. AT24C32C/64C, 32/64K SERIAL EEPROM: The 32K/64K is internally organized as 128/256 pages of 32 bytes each. Random word addressing requires a 12/13 bit data word address. ...

Page 4

Pin Capacitance Applicable over recommended operating range from T Symbol Test Condition C Input/Output Capacitance (SDA) I/O C Input Capacitance ( Note: 1. This parameter is characterized and is not 100% tested. DC Characteristics Applicable ...

Page 5

AC Characteristics Applicable over recommended operating range from T 100 pF (unless otherwise noted) Symbol Parameter f Clock Frequency, SCL SCL t Clock Pulse Width Low LOW t Clock Pulse Width High HIGH t Noise Suppression Time i t Clock ...

Page 6

... EEPROM in 8-bit words. The EEPROM sends a zero during the ninth clock cycle to acknowledge that it has received each word. STANDBY MODE: The AT24C32C/64C features a low power standby mode which is enabled: a) upon power-up and b) after the receipt of the Stop bit and the completion of any internal operations ...

Page 7

Bus Timing SCL: Serial Clock, SDA: Serial Data I/O Write Cycle Timing SCL: Serial Clock, SDA: Serial Data I/O SCL SDA 8th BIT WORDn Note: 1. The write cycle time t is the time from a valid stop condition of ...

Page 8

Data Validity Start and Stop Definition Output Acknowledge 5174B–SEEPR–12/06 8 ...

Page 9

... Upon a compare of the device address, the EEPROM will output a zero compare is not made, the device will return to standby state. DATA SECURITY: The AT24C32C/64C has a hardware data protection scheme that allows the user to write protect the entire memory when the WP pin ...

Page 10

... The address “roll over” during read is from the last byte of the last memory page, to the first byte of the first page. The address “roll over” during write is from the last byte of the cur- rent page to the first byte of the same page ...

Page 11

... Figure 1. Device Address Figure 2. Byte Write Figure 3. Page Write Note DON’T CARE bits DON’T CARE bit for AT24C32C Figure 4. Current Address Read 5174B–SEEPR–12/ ...

Page 12

Figure 5. Random Read Note DON’T CARE bits Figure 6. Sequential Read 5174B–SEEPR–12/06 12 ...

Page 13

... AT24C32C Ordering Information Ordering Code AT24C32C-PU (Bulk form only) (1) AT24C32CN-SH-B (NiPdAu Lead Finish) (2) AT24C32CN-SH-T (NiPdAu Lead Finish) (1) AT24C32C-TH-B (NiPdAu Lead Finish) (2) AT24C32C-TH-T (NiPdAu Lead Finish) (2) AT24C32CY6-YH-T (NiPdAu Lead Finish) (2) AT24C32CU2-UU-T (3) AT24C32C-W-11 Notes: 1. “-B” denotes Bulk. 2. “-T” denotes tape and reel. SOIC = 4K per reel. TSSOP, Ultra Thin Mini-MAP and dBGA2 = 5K per reel. ...

Page 14

AT24C64C Ordering Information Ordering Code AT24C64C-PU (Bulk form only) (1) AT24C64CN-SH-B (NiPdAu Lead Finish) (2) AT24C64CN-SH-T (NiPdAu Lead Finish) (1) AT24C64C-TH-B (NiPdAu Lead Finish) (2) AT24C64C-TH-T (NiPdAu Lead Finish) (2) AT24C64CY6-YH-T (NiPdAu Lead Finish) (2) AT24C64CU2-UU-T (3) AT24C64C-W-11 Notes: 1. ...

Page 15

Packaging Information 8Y6 - MLP D Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-229, for proper dimensions, tolerances, datums, etc. 2. Dimension b applies to metallized terminal and is measured between 0.15 mm and ...

Page 16

PDIP Top View PLCS Side View Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information. 2. Dimensions A and L are measured with the ...

Page 17

JEDEC SOIC TOP VIEW TOP VIEW e e SIDE VIEW SIDE VIEW Note: These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 1150 E. Cheyenne Mtn. Blvd. ...

Page 18

TSSOP Pin 1 indicator this corner N Top View Side View Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, ...

Page 19

A1 BALL PAD CORNER e (e1) 5. Dimension 'b' is measured at the maximum solder ball diameter. This drawing is for general information only. 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 R 5174B–SEEPR–12/ ...

Page 20

... Revision History Doc. Rev. 5174B 5174A 5174B–SEEPR–12/06 Comments Added AT24C32C offering Added 8U2-1 package drawing Added 1.8 voltage to ordering information pages of AT24C32C and AT24C64C Initial document release 20 ...

Page 21

... Atmel Corporation. All rights reserved. Atmel marks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 ...