STK14D88_08 SIMTEK [Simtek Corporation], STK14D88_08 Datasheet - Page 11
![no-image](/images/no-image-200.jpg)
STK14D88_08
Manufacturer Part Number
STK14D88_08
Description
32Kx8 Autostore nvSRAM
Manufacturer
SIMTEK [Simtek Corporation]
Datasheet
1.STK14D88_08.pdf
(20 pages)
Document Control #ML0033 Rev 2.0
nvSRAM
The STK14D88 nvSRAM is made up of two func-
tional components paired in the same physical cell.
These are the SRAM memory cell and a nonvolatile
QuantumTrap cell. The SRAM memory cell operates
like a standard fast static RAM. Data in the SRAM
can be transferred to the nonvolatile cell (the
STORE operation), or from the nonvolatile cell to
SRAM (the RECALL operation). This unique archi-
tecture allows all cells to be stored and recalled in
parallel. During the STORE and RECALL operations
SRAM READ and WRITE operations are inhibited.
The STK14D88 supports unlimited read and writes
like a typical SRAM. In addition, it provides unlimited
RECALL operations from the nonvolatile cells and
up to 200K STORE operations.
SRAM READ
The STK14D88 performs a READ cycle whenever E
and G are low while W and HSB are high. The
address specified on pins A
the 32,768 data bytes will be accessed. When the
READ is initiated by an address transition, the out-
puts will be valid after a delay of t
#1). If the READ is initiated by E and G, the outputs
will be valid at t
(READ cycle #2). The data outputs will repeatedly
respond to address changes within the t
access time without the need for transitions on any
control input pins, and will remain valid until another
address change or until either E or G is brought
high, or W or HSB is brought low.
Jan 2008
Figure 3: AutoStore Mode
ELQV
V
CAP
or at t
GLQV
V
0-16
W
CC
determine which of
, whichever is later
AVQV
nvSRAM OPERATION
(READ cycle
V
CC
AVQV
11
SRAM WRITE
A WRITE cycle is performed whenever E and W are
low and HSB is high. The address inputs must be
stable prior to entering the WRITE cycle and must
remain stable until either E or W goes high at the
end of the cycle. The data on the common I/O pins
DQ0-7 will be written into memory if it is valid t
before the end of a W controlled WRITE or t
before the end of an E controlled WRITE.
It is recommended that G be kept high during the
entire WRITE cycle to avoid data bus contention on
common I/O lines. If G is left low, internal circuitry
will turn off the output buffers t
low.
AutoStore OPERATION
The STK14D88 stores data to nvSRAM using one of
three storage operations. These three operations
are Hardware Store (activated by HSB), Software
Store (activated by an address sequence), and
AutoStore (on power down).
AutoStore operation is a unique feature of Simtek
Quantum Trap technology is enabled by default on
the STK14D88.
During normal operation, the device will draw cur-
rent from V
the V
chip to perform a single STORE operation. If the
voltage on the V
part will automatically disconnect the V
V
provided by the V
Figure 3 shows the proper connection of the storage
capacitor (V
Refer to the DC CHARACTERISTICS table for the
size of the capacitor. The voltage on the V
driven to 5V by a charge pump internal to the chip. A
pull up should be placed on W to hold it inactive dur-
ing power up.
To reduce unneeded nonvolatile stores, AutoStore
and Hardware Store operations will be ignored
unless at least one WRITE operation has taken
place since the most recent STORE or RECALL
cycle. Software initiated STORE cycles are per-
formed regardless of whether a WRITE operation
CC
. A STORE operation will be initiated with power
CAP
pin. This stored charge will be used by the
CC
CAP
to charge a capacitor connected to
) for automatic store operation.
CC
CAP
pin drops below V
capacitor.
WLQZ
STK14D88
after W goes
CAP
SWITCH
CAP
pin from
DVWH
pin is
DVEH
, the