EPC100 EPC [Espros Photonics corp], EPC100 Datasheet
EPC100
Related parts for EPC100
EPC100 Summary of contents
Page 1
... Up to 1023 devices may be connected to two respectively four wires in paral- lel. Each device can be individually addressed by an epc100 chip which acts as the interface between a microcontroller and the 2- wire bus. It manages the bus traffic between the microcontroller and the individual Rx and Tx elements ...
Page 2
... DD 3.0 DD33 ) -40° Values Min. Typ. PD NST 36nA 48nA 72nA 108nA 50 6.4 8 un- Relax 2.4 0 GND 0 0.5 DD 0.7 0.1 30 Datasheet epc100 - V2.1 www.espros.ch epc100 Max. Units 5.5 V 8.0 V 3.6 V +85 °C +95 % Units Max 150 mV 350 mV 600 mV 1.4 mA 2.0 mA 200 mV 9 108 nA nA 100 µ ...
Page 3
... File: Unbenannt This document is confidential and protected by law and international trades. It must not be shown to any third party nor be copied in any form without our written permission 3 epc100 Top View 16-Pin QFN Package , a DDR 28.01.2010 LST Page 1 Datasheet epc100 - V2.1 www.espros.ch . ...
Page 4
... ESPROS Photonics Corporation Characteristics subject to change without notice Pulse width [us] Figure 1: Input Sensitivity vs. LED pulse length Threshold OUTH OUTN OUTN OUTH Figure 2: OUTN and OUTH threshold operation Figure 3: Typical light curtain receiver edge circuit Datasheet epc100 - V2.1 www.espros.ch epc100 ...
Page 5
... CS GND GND The epc100 device can be operated in two different modes: a) Photo Current Receivers It detects current pulses of the photo diode generated by light pulses and transmits the information using the 2-wire bus to a central con - troller, i.e. a micro controller. The devices operating as this photo current receivers are designated in the schematic diagram above ...
Page 6
... The pins at the bottom are to solder the shield to the PCB with electrical connection to GND. The hole in the front is the opening window for the photo diode. The back side of the PCB below the sensitive area (PD, epc100) shall be a polygon connected to GND to shield the circuit from the back side. The capacitors shall be of high mechanical stability (no piezoelectric effect) in order to avoid unwanted voltage modulation by mechanical shock or vibration ...
Page 7
... Approved <Name> <Data> Scale M 1:1 DIN A4 Page 1 Part Name Part No. <Partname> <x000 000> File: Unbenannt Pin 1 Solder balls Sn97.5Ag2.5 7 Layout Recommendations 0.1524 ∅ 0.3 0.5 0.5 2.5 no solder mask inside this area Bottom View <name> . 0.25 LST . Datasheet epc100 - V2.1 epc100 20.12.2011 Page 1 0.3 18.05.2011 Page 1 www.espros.ch ...
Page 8
... Package RoHS compliance CSP10 Yes QFN16 Yes CSP10 Yes QFN16 Yes 8 Pin 1 ) should not exceed +260°C for a maximum of 4 sec. 8 Pin 1 8 Packaging Method Reel Reel Reel Reel Datasheet epc100 - V2.1 epc100 www.espros.ch ...
Page 9
... ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, epc will not be responsible for any failure to meet such requirements. © 2011 ESPROS Photonics Corporation Characteristics subject to change without notice 9 epc100 Datasheet epc100 - V2.1 www.espros.ch ...