LX2206ILD MICROSEMI [Microsemi Corporation], LX2206ILD Datasheet - Page 2
![no-image](/images/no-image-200.jpg)
LX2206ILD
Manufacturer Part Number
LX2206ILD
Description
Dual Level Lithium Ion Battery Charger
Manufacturer
MICROSEMI [Microsemi Corporation]
Datasheet
1.LX2206ILD.pdf
(14 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LX2206ILD
Manufacturer:
MICROSEMI/美高森美
Quantity:
20 000
Company:
Part Number:
LX2206ILD(2206)
Manufacturer:
VISHAY
Quantity:
180
Copyright © 2005
Rev. 1.2, 2006-12-22
DCOK
Supply Input Voltage (IN, BAT) ...................................................................... -0.3V to 7V
All other pins ............................................................................................-0.3V to V
Battery Charging Current .............................................................................................1.1A
Operating Temperature Range .........................................................................-40 to 150°C
Maximum Operating Junction Temperature .............................................................. 150°C
Storage Temperature Range.........................................................................-65°C to 150°C
Lead Temperature (Soldering 10 seconds)................................................................. 300°C
Package Peak Temp. for Solder Reflow (40 seconds maximum exposure) ... 260°C (+0 -5)
Note: Exceeding these ratings could cause damage to the device. All voltages are with respect to
Junction Temperature Calculation: T
The θ
above assume no ambient airflow.
Name
STAT
CMP
GND
HCP
TMP
BAT
LCP
LD
H/L
SD
IN
THERMAL RESISTANCE
JA
Ground. Currents are positive into, negative out of specified terminal
TM
numbers are guidelines for the thermal performance of the device/pc-board system. All of the
Plastic Micro Leadframe Package 10-Pin
Battery – Connect to a single cell Lithium Ion Battery.
Compensation – Connect the series combination of a 1k resistor and a 0.47µF capacitor from CMP to IN.
Power status logic pin and LED driver – This pin is an open drain output that can sink 20mA of current to drive an
external LED. This pin is low impedance to GND when the Input voltage is high enough to charge the Battery.
Ground – Connect to the system ground plane. Use sufficient via copper area to allow for thermal conduction
from the IC to the GND plane.
High Current Programming (and Termination Current Programming) – Connect a resistor to ground to set the
constant current high level. The termination current is set to 1/10 of the High Current Programming Level.
For a value of 19.6K, the High Current is 460mA and the Termination Current is 46mA.
High or Low load select logic input – A logic high selects the constant charge current level set by the HCP pin
resistor and a logic low selects the constant charge current level set by the LCP pin resistor
Input Power – Connect to a wall adapter or a USB power plug.
Low Current Programming – Connect a resistor to ground to set the constant current low level.
For a value of 110K, the Low Current is 92mA.
Shutdown – A logic high places the LX2206 in sleep mode; can also be used for USB suspend.
Charging status logic pin and LED driver – This pin can source or sink 10mA of current to drive an external LED
in either output state. This pin is low (current sinking mode) when the battery is in charging mode and becomes
high (current sourcing mode) when the charge cycle is finished. It becomes a high impedance when the input
power is removed.
Battery Temperature Monitor – This sense pin determines the battery temperature for charging out of
temperature range lockout and is connected to a resistor network as defined in the Applications section. The
TMP pin is grounded if this function is not used.
A B S O L U T E M A X I M U M R A T I N G S
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
-
JUNCTION TO
T H E R M A L D A T A
J
= T
A
+ (P
F U N C T I O N A L P I N D E S C R I P T I O N
D
x θ
A
JA
MBIENT
).
Integrated Products Division
, θ
®
Microsemi
JA
Description
.
Dual Level Lithium Ion Battery Charger
49°C/W
SUPPLY
P
RODUCTION
DCOK
STAT
RoHS / Pb-free 100% matte Tin Lead Finish
CMP
SD
D
IN
P A C K A G E P I N O U T
ATA
1
2
3
4
5
S
LD P
HEET
Bottom PAD to
ACKAGE
(Top View)
Connect
GND
P
INOUT
LX2206
10
9
8
7
6
BAT
TMP
HCP
LCP
H/L
Page 2