SE95 PHILIPS [NXP Semiconductors], SE95 Datasheet
![no-image](/images/no-image-200.jpg)
SE95
Available stocks
Related parts for SE95
SE95 Summary of contents
Page 1
... SE95 Ultra high accuracy digital temperature sensor and thermal Watchdog Product data sheet Supersedes data of 2004 Oct 05 INTEGRATED CIRCUITS 2004 Dec 21 ...
Page 2
... There are three selectable logic address pins so that eight devices can be connected on the same bus without address conflict. The SE95 can be configured for different operation conditions. It can be set in normal mode to periodically monitor the ambient temperature shutdown mode to minimize power consumption. ...
Page 3
... BANK INTERFACE LOGIC SCL SDA Figure 2. Simplified block diagram. 3 Product data sheet SE95 DESCRIPTION 2 Digital I/ serial bi-directional data line. Open Drain. 2 Digital input serial clock input. Overtemp Shutdown output. Open Drain. Ground connected to the system ground. ...
Page 4
... POWER SUPPLY CC 0 SCL 1 SDA SE95 /GND GND 4 Figure 3. Typical application circuit PARAMETER PARAMETER 4 Product data sheet SE95 DETECTOR OR INTERRUPT LINE SL01883 MIN. MAX. UNIT –0.3 6.0 V –0.3 6.0 V –3 0 –5.0 5.0 mA – 10.0 mA –0.3 6.0 V – 1000 V – ...
Page 5
... SDA and OS pins supply below which the logic CC is reset Programmable Default value Programmable 0.125 Default value Digital pins = Product data sheet SE95 2 TYP. MAX. UNIT – +1.0 C – +2.0 C –2 – –3 – – 0.125 – ...
Page 6
... SCL t HD;STA t HD;DAT S 2004 Dec 21 1 CONDITIONS See timing diagram (Figure 400 pF HD;STA t HIGH Sr Figure 4. Timing diagram. 6 Product data sheet SE95 MIN. TYP. MAX. UNIT 2.5 – – s 0.6 – – s 1.3 – – s 100 – – ns 100 – ...
Page 7
... SL02152 Figure 9. Typical conversion time versus temperature 0.25 0.20 0.15 0.10 0.05 0.00 75 100 125 –50 SL02151 Figure 10. Typical 3 Product data sheet SE95 – 100 TEMPERATURE ( C) SL02153 versus temperature and mA) OL – ...
Page 8
... Watchdog FUNCTIONAL DESCRIPTION General operation The SE95 uses the on-chip band-gap sensor to measure the device temperature with the resolution of 0.03125 C and stores the 13-bit 2’s complement digital data, resulted from 13-bit A-to-D conversion, into the device Temp register. This Temp register can be read at any ...
Page 9
... OS is reset by either reading register or putting the device in shutdown. Assumed that the fault queue is met at each Tos and Thyst crossing point. 2004 Dec 21 Temp READING TEMPERATURE & LIMITS OS OUTPUT IN COMPARATOR MODE * * OS OUTPUT IN INTERRUPT MODE Figure 11. OS response to temperature. 9 Product data sheet SE95 * SL01392 ...
Page 10
... N/A 2004 Dec 21 Register list The SE95 contains 7 data registers. The registers can be 1 byte or 2 bytes wide, and are defined in Table 2. The registers are accessed by the value in the content of the pointer register during I communication. The types of registers are: read only, read/write, ...
Page 11
... LSB MSB LSB Value Resolution Value Resolution Value resolution 1.0 C 0.5 C 0.25 C 0.125 C 0.0625 C 0.03125 C 11 Product data sheet SE95 Temp LS byte LSB Not used Not used LSB ...
Page 12
... Obviously, for 9-bit Temp data application in replacing the industry standard LM75, just use only 9 MSB bits of the two bytes and disregard 7 LSB bits of the LS byte. The 9-bit temp data with 0.5 C resolution of the SE95 is defined exactly in the same way as for the standard LM75 and it is here similar to the Tos and Thyst that is described next ...
Page 13
... If the OS output is in comparator mode, then it remains unchanged. In Interrupt mode, the OS output is reset. Power-up default and Power-on Reset The SE95 always powers-up in its default state with: – Normal operation mode – OS comparator mode – Tos = 80 C – Thyst = 75 C – ...
Page 14
... R: Read bit, when the Write/Read bit = HIGH in a read command Device Acknowledge bit, returned by the SE95 LOW if the device works properly and HIGH if not. The host must release the SDA line during this period in order to give the device the control on the SDA line ...
Page 15
... DATA BYTE FROM DEVICE DEVICE MASTER NOT ACKNOWLEDGE ACKNOWLEDGED 15 Product data sheet SE95 CONFIGURATION DATA BYTE STOP DEVICE DEVICE ACKNOWLEDGE ACKNOWLEDGE SL01393 ...
Page 16
... ACKNOWLEDGE ACKNOWLEDGE BYTE FROM DEVICE DEVICE MASTER ACKNOWLEDGE ACKNOWLEDGE 16 Product data sheet SE95 9 (next) (next STOP SL01397 9 0 (next) RS (next) RE-START ...
Page 17
... Philips Semiconductors Ultra high accuracy digital temperature sensor and thermal Watchdog SO8: plastic small outline package; 8 leads; body width 3.9 mm 2004 Dec 21 17 Product data sheet SE95 SOT96-1 ...
Page 18
... Philips Semiconductors Ultra high accuracy digital temperature sensor and thermal Watchdog TSSOP8: plastic thin shrink small outline package; 8 leads; body width 3 mm 2004 Dec 21 18 Product data sheet SE95 SOT505-1 ...
Page 19
... C-bus interface with devices on the same bus” to “I Machine Model (max.) from ‘100 V’ to ‘150 V’ esd : = 2 3 – 100 C” to “T = – +100 C” amb amb = – –125 C” to “T = – +125 C” amb amb 19 Product data sheet SE95 2 C-bus interface to ...
Page 20
... Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Fax: + 24825 Document number: 20 Product data sheet SE95 2 C patent Koninklijke Philips Electronics N.V. 2004 All rights reserved. Published in the U.S.A. Date of release: 12-04 ...