LM80CIMT-5 NSC [National Semiconductor], LM80CIMT-5 Datasheet - Page 3
![no-image](/images/no-image-200.jpg)
LM80CIMT-5
Manufacturer Part Number
LM80CIMT-5
Description
Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor
Manufacturer
NSC [National Semiconductor]
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM80CIMT-5
Manufacturer:
national
Quantity:
2
Part Number:
LM80CIMT-5
Manufacturer:
NS/国半
Quantity:
20 000
Company:
Part Number:
LM80CIMT-5/NOPB
Manufacturer:
NS
Quantity:
3 843
Company:
Part Number:
LM80CIMT-5/NOPB
Manufacturer:
NS/TI
Quantity:
3 500
FAN1-FAN2
BTI
CI (Chassis
Intrusion)
GND
V
+5.75V)
INT
GPO (Power
Switch Bypass)
NTEST_IN/
RESET_IN
RST_OUT/OS
GNDA
IN6-IN0
A0/NTEST_OUT
A1-A2
TOTAL PINS
+
Pin Descriptions
(+2.8V to
Name(s)
Pin
Number
15-21
23-24
Pin
4-5
10
11
12
13
14
22
6
7
8
9
(Continued)
Number
of Pins
24
2
1
1
1
1
1
1
1
1
1
7
1
2
Digital Inputs
Digital Input
Digital I/O
GROUND
POWER
Digital Output
Digital Output
Digital Input
Digital Output
GROUND
Analog Inputs
Digital I/O
Digital Inputs
Type
0 to V
Board Temperature Interrupt driven by O.S. outputs of additional
temperature sensors such as LM75. Provides internal pull-up of
10 k .
An active high input from an external circuit which latches a Chassis
Intrusion event. This line can go high without any clamping action
regardless of the powered state of the LM80. The LM80 provides an
internal open drain on this line, controlled by Bit 5 of the
Configuration Register, to provide a minimum 10 ms reset of this
line.
Internally connected to all of the digital circuitry.
+3.3V or +5V V
10 µF (electrolytic or tantalum) and 0.1 µF (ceramic) bypass
capacitors.
Non-Maskable Interrupt (open source)/Interrupt Request (open
drain). The mode is selected with Bit 5 of the Configuration Register
and the output is enabled when Bit 1 of the Configuration Register
is set to 1. The default state is disabled.
An active low open drain output intended to drive an external
P-channel power MOSFET for software power control.
An active-low input that enables NAND Tree board-level connectivity
testing. Refer to Section 10.0 on NAND Tree testing. Whenever
NAND Tree connectivity is enabled the LM80 is also reset to its
power on state.
Master Reset, 5 mA driver (open drain), active low output with a
10 ms minimum pulse width. Available when enabled via Bit 4 in
Configuration Register and Bit 7 of the Fan Divisor/RST_OUT/OS
Register. Bit 6 of the Fan Divisor/RST_OUT/OS Register enables
this output as an active low Overtemperature Shutdown (OS).
Internally connected to all analog circuitry. The ground reference for
all analog inputs. This pin needs to be taken to a low noise analog
ground plane for optimum performance.
0V to 2.56V full scale range Analog Inputs.
The lowest order bit of the Serial Bus Address. This pin functions as
an output when doing a NAND Tree test.
The two highest order bits of the Serial Bus Address.
3
+
fan tachometer inputs.
+
power. Bypass with the parallel combination of
Description
www.national.com