LPC2132 PHILIPS [NXP Semiconductors], LPC2132 Datasheet - Page 29
LPC2132
Manufacturer Part Number
LPC2132
Description
Single-chip 16/32-bit microcontrollers; 32/64/512 kB ISP/IAP Flash with 10-bit ADC and DAC
Manufacturer
PHILIPS [NXP Semiconductors]
Datasheet
1.LPC2132.pdf
(41 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LPC2132FBD/01
Manufacturer:
NXP
Quantity:
25 000
Company:
Part Number:
LPC2132FBD64
Manufacturer:
PHILIPS
Quantity:
5
Part Number:
LPC2132FBD64
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
LPC2132FBD64,151
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
LPC2132FBD64/01
Manufacturer:
NXP
Quantity:
5 530
Company:
Part Number:
LPC2132FBD64/01
Manufacturer:
NXP
Quantity:
2 844
Part Number:
LPC2132FBD64/01
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
LPC2132FBD64/01,11
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
LPC2132FBD64/01,15
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
LPC2132FBD64/01.151
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Philips Semiconductors
7. Limiting values
Table 9:
In accordance with the Absolute Maximum Rating System (IEC 60134).
[1]
[2]
[3]
[4]
[5]
[6]
9397 750 14868
Preliminary data sheet
Symbol
V
V
V
V
V
V
V
I
I
T
P
DD
SS
stg
DD
DDA
BAT
REF
IA
I
I
tot(pack)
The following applies to the Limiting values:
a) Stresses above those listed under Limiting values may cause permanent damage to the device. This is a stress rating only and
b) This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive
c) Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to V
Including voltage on outputs in 3-state mode.
Only valid when the V
Not to exceed 4.6 V.
The peak current is limited to 25 times the corresponding maximum current.
Dependent on package type.
functional operation of the device at these or any conditions other than those described in
Section 9 “Dynamic characteristics”
static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated maximum.
otherwise noted.
Limiting values
Parameter
supply voltage, core and external rail
analog 3.3 V pad supply voltage
RTC power supply voltage
A/D converter reference voltage
analog input voltage on A/D related pins
DC input voltage, 5 V tolerant I/O pins
DC input voltage, other I/O pins
DC supply current per supply pin
DC ground current per ground pin
storage temperature
total power dissipation
DD
supply voltage is present.
[6]
of this specification is not implied.
Rev. 02 — 15 April 2005
LPC2131/2132/2134/2136/2138
Conditions
based on package
heat transfer, not
device power
consumption
[1]
Single-chip 16/32-bit microcontrollers
[2] [3]
[2]
Min
-
-
-
0.5
0.5
0.5
0.5
0.5
0.5
0.5
40
Section 8 “Static
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Max
+3.6
4.6
4.6
4.6
5.1
6.0
V
0.5
100
100
125
1.5
DD
[4]
characteristics”and
[5]
[5]
+
SS
Unit
V
V
V
V
V
V
V
mA
mA
W
C
unless
29 of 41