MC9S08GT16 MOTOROLA [Motorola, Inc], MC9S08GT16 Datasheet - Page 54
MC9S08GT16
Manufacturer Part Number
MC9S08GT16
Description
Microcontrollers
Manufacturer
MOTOROLA [Motorola, Inc]
Datasheet
1.MC9S08GT16.pdf
(290 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MC9S08GT16ACBE
Manufacturer:
SHARP
Quantity:
1 200
Company:
Part Number:
MC9S08GT16ACFBE
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
MC9S08GT16ACFBER
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MC9S08GT16ACFBER
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
MC9S08GT16AMFBE
Manufacturer:
XILINX
Quantity:
1 300
Company:
Part Number:
MC9S08GT16AMFBE
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
MC9S08GT16CFBE
Manufacturer:
FREESCALE
Quantity:
1 831
Part Number:
MC9S08GT16CFBE
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
MC9S08GT16CFD
Manufacturer:
FREESCALE
Quantity:
20 000
Chapter 4 Memory
4.6.1
Bit 7 of this register is a read-only status flag. Bits 6 through 0 may be read at any time but can be written
only one time. Before any erase or programming operations are possible, write to this register to set the
frequency of the clock for the nonvolatile memory system within acceptable limits.
DIVLD — Divisor Loaded Status Flag
PRDIV8 — Prescale (Divide) FLASH Clock by 8
DIV5:DIV0 — Divisor for FLASH Clock Divider
Table 4-6
54
When set, this read-only status flag indicates that the FCDIV register has been written since reset.
Reset clears this bit and the first write to this register causes this bit to become set regardless of the
data written.
The FLASH clock divider divides the bus rate clock (or the bus rate clock divided by 8 if PRDIV8 = 1)
by the value in the 6-bit DIV5:DIV0 field plus one. The resulting frequency of the internal FLASH
clock must fall within the range of 200 kHz to 150 kHz for proper FLASH operations. Program/erase
timing pulses are one cycle of this internal FLASH clock, which corresponds to a range of 5 µs to
6.7 µs. The automated programming logic uses an integer number of these pulses to complete an erase
or program operation.
1 = FCDIV has been written since reset; erase and program operations enabled for FLASH.
0 = FCDIV has not been written since reset; erase and program operations disabled for FLASH.
1 = Clock input to the FLASH clock divider is the bus rate clock divided by 8.
0 = Clock input to the FLASH clock divider is the bus rate clock.
shows the appropriate values for PRDIV8 and DIV5:DIV0 for selected bus frequencies.
FLASH Clock Divider Register (FCDIV)
Reset:
Read:
Write:
if PRDIV8 = 1 — f
if PRDIV8 = 0 — f
Figure 4-4. FLASH Clock Divider Register (FCDIV)
DIVLD
Bit 7
0
= Unimplemented or Reserved
PRDIV8
MC9S08GB/GT Data Sheet, Rev. 2.3
6
0
FCLK
FCLK
= f
= f
Bus
DIV5
5
0
Bus
÷ (8 × ([DIV5:DIV0] + 1))
÷ ([DIV5:DIV0] + 1)
DIV4
4
0
DIV3
3
0
DIV2
2
0
DIV1
Freescale Semiconductor
1
0
DIV0
Bit 0
0
Eqn. 4-1
Eqn. 4-2