AK5392-VS AKM [Asahi Kasei Microsystems], AK5392-VS Datasheet
![no-image](/images/no-image-200.jpg)
AK5392-VS
Available stocks
Related parts for AK5392-VS
AK5392-VS Summary of contents
Page 1
... The AK5392 is a 24bit, 128x oversampling 2ch A/D Converterfor professional digital audio systems. The modulator in the AK5392 uses the new developed Enhanced Dual Bit architecture. This new architecture achieves the wider dynamic range, while keeping much the same superior distortion characteristics as conventional Single Bit way. The AK5392 performs 116dB dynamic range, so the device is suitable for professional studio equipments such as digital mixer, digital VTR etc ...
Page 2
... ASAHI KASEI Ordering Guide AK5392-VS AKD5392 Pin Layout Compatibility with AK5391 1. Changed Specs Parameter HPF Output Resolution DR Input Offset 2. Pin Compatibility The following pin functions are changed from AK5391. AK5392 supports 24bit only. Pin No. AK5391 2 VREFL- 19 SEL24 27 VREFR- 0188-E-01 C -10 +70 28pin SOP ...
Page 3
... SMODE1 "H". 0188-E-01 PIN/FUNCTION Function RST goes "H". CAL goes "L" after 8704 LRCK cycles. MODE L L Slave mode : MSB justified L H Master mode : Similar to I2S H L Slave mode : I2S H H Master mode : I2S - 3 - [AK5392] LRCK : H/L : H/L : L/H : L/H 1997/11 ...
Page 4
... SCLK requires more than 48fs clock. SCLK outputs a 128fs clock. SCLK stays "L" during reset. When "H", the data bits are clocked out on SDATA. FSYNC outputs 2fs clock. FSYNC stays "L" during reset [AK5392] 1997/11 ...
Page 5
... The power up sequence between VA and VD is not critical. * AKM assumes no responsibility for the usage beyond the conditions in this data sheet. 0188-E-01 ABSOLUTE MAXIMUM RATINGS Symbol min VA -0.3 VD -0.3 GND IIN VINA -0.3 VIND -0.3 Ta -10 Tstg -65 Symbol min VA 4. [AK5392] max Units 6 ±10 mA VA+0.3 V VD+0 150 typ max Units 5.0 5.25 V 3.3 5 ...
Page 6
... Units Bits 0 ppm/ 150 LSB 24 LSB 24 C LSB / - 24 mV ±2. 130 ...
Page 7
... Input Leakage Current 0188-E-01 FILTER CHARACTERISTICS Symbol min 26.232 PR SA 110 GD GD -3dB FR -0.5dB -0.1dB DIGITAL CHARACTERISTICS Symbol min VIH 70%VD VIL - VOH VD-0.1 VOL - Iin - - 7 - [AK5392] typ max Units 21.768 kHz kHz dB ±0.001 38.7 1/fs 1.0 Hz 2.9 Hz 6.5 Hz typ max Units - - V - 30% ...
Page 8
... RST brought high. The value is in master mode [AK5392] Typ Max Units 12.288 13.824 MHz ns ns 18.432 20.736 MHz ns ns 6.144 6.912 MHz 48 54 kHz ...
Page 9
... ASAHI KASEI Timing Diagram 0188-E- [AK5392] 1997/11 ...
Page 10
... ASAHI KASEI 0188-E- [AK5392] 1997/11 ...
Page 11
... Therefore, the reset is only needed for power-up. fs 32.0kHz 44.1kHz 48.0kHz Serial Data Interface AK5392 supports four serial data formats which can be selected via SMODE1 and SMODE2 pins(Table 2 ). The data format is MSB-first, 2's complement. Figure SMODE2 Figure 1 Figure 2 ...
Page 12
... ASAHI KASEI 0188-E- [AK5392] 1997/11 ...
Page 13
... With ZCAL "H", the analog input pin voltages are measured, and with ZCAL "L", the VCOM pin voltages are measured. The CAL output is "H" during calibration. Digital High Pass Filter The AK5392 also has a digital high pass filter for DC offset cancel. The cut-off frequency of the HPF is 1Hz at fs=48kHz and also scales with sampling rate(fs). 0188-E-01 ...
Page 14
... ASAHI KASEI Figure 5 shows the system connection diagram. An evaluation board[AKD5392] is available which demonstrates the optimum layout, power supply arrangements and measurement results. 0188-E-01 SYSTEM DESIGN Figure 5 . Typical Connection Diagram - 14 - [AK5392] 1997/11 ...
Page 15
... VCOM is a common voltage of the analog signal. In order to eliminate the effects of high frequency noise, a 0.22uF ceramic capacitor should be connected as near to the VCOM pin as possible. And all signals, especially clocks, should be kept away from the VCOM pin in order to avoid unwanted coupling into the AK5392. No load current may be drawn from the VCOM pin. ...
Page 16
... ADC. This circuit is also a low pass filter with cut-off frequency of about 220kHz. In this example, the internal offset is removed by self calibration. The evaluation board should be refered about the detail. Figure 6 . Differential Input Buffer Example 0188-E- [AK5392] 1997/11 ...
Page 17
... ASAHI KASEI 28pin SOP (Unit: mm) Package & Lead frame material Package molding compound : Lead frame material : Lead frame surface treatment : 0188-E-01 PACKAGE Epoxy Cu Solder plate - 17 - [AK5392] 1997/11 ...
Page 18
... ASAHI KASEI Contents of XXXBYYYYC XXXB: Lot #(X:numbers,B:alphabet) YYYYC: Date Code(Y:numbers,C:alphabet) 0188-E-01 MARKING - 18 - [AK5392] 1997/11 ...
Page 19
IMPORTANT NOTICE These products and their specifications are subject to change without notice. Before considering any use or application, consult the Asahi Kasei Microsystems Co., Ltd. (AKM) sales office or authorized distributor concerning their current status. AKM assumes no liability ...