PEX8548-AA25BI PLX [PLX Technology], PEX8548-AA25BI Datasheet - Page 2

• Manufacturer Part Number: PEX8548-AA25BI
• Description: High-Performance 48-lane, 9-port PCIe Switch
• Manufacturer: PLX [PLX Technology]

Low Power with Granular SerDes Control
The PEX 8548 provides low power capability that is
fully compliant with the PCI Express power
management specification. In addition, the SerDes
physical links can be turned off when unused for even
lower power.
Flexible Port Width Configuration
The width of each port can be individually configured
through auto-negotiation, hardware strapping, host
software configuration, I
optional EEPROM.
The PEX 8548 supports a large number of port
configurations (see Figure 1). For example, if you are
using the PEX 8548 in a fan-out application, you may
configure the upstream port as a x16 and the
downstream as eight x4 ports; three x8 ports & two x4
ports; or various combinations, as long as you don’t run
out of lanes (48) or ports (9). For a dual-graphics
application, the device can be configured as three x16
ports.
Low Packet Latency
The PEX 8548 supports packet cut-thru with a
maximum packet latency of 110ns between symmetric
x16 ingress and egress ports. The low latency enables
applications to achieve high throughput and
performance. In addition to low latency, the device
supports a packet payload size of up to 1024 bytes,
enabling the user to achieve even higher throughput.
Hot Plug for High Availability
Hot plug capability allows users to replace hardware
modules and perform maintenance without powering
down the system. The PEX 8548 hot plug capability and
Figure 1. Common Port Configurations
x8
x8
PEX 8548
PEX 8548
PEX 8548
PEX 8548
PEX 8548
PEX 8548
PEX 8548
PEX 8548
all x8
x4
x4
x16
x8
x4 x4
2
C interface, or through an
x8
PEX 8548
PEX 8548
PEX 8548
PEX 8548
PEX 8548
PEX 8548
x8
PEX 8548
PEX 8548
x16
x8
x16
x16
x4 x4
x16
advanced error reporting features make it suitable for
High Availability (HA) applications. Three
downstream ports include a Standard Hot Plug
Controller. If the PEX 8548 is used in an application
where one or more of its downstream ports connect to
PCI Express slots, each port’s Hot Plug Controller can
be used to manage the hot-plug event of its associated
slot. Furthermore, its upstream port is a hot-plug client,
allowing it to be used on hot-pluggable adapter cards,
backplanes, and fabric modules.
Fully Compliant Power Management
For applications that require power management, the
PEX 8548 device supports both link (L0, L0s, L1, L2/L3
Ready, and L3) and device (D0 and D3hot) power
management states, in compliance with the PCI Express
power management specification.
SerDes Power and Signal Management
The PEX 8548 supports software control of the SerDes
outputs to allow optimization of power and signal
strength in a system. The PLX SerDes implementation
supports four levels of power – off, low, typical, and
high. The SerDes block also supports loop-back modes
and advanced reporting of error conditions, which
enables efficient debug and management of the entire
system.
Applications
Suitable for host-centric as well as peer-to-peer traffic
patterns, the PEX 8548 can be configured for a wide
variety of form factors and applications.
Host Centric Fan-out
The PEX 8548, with its symmetric or asymmetric lane
configuration capability, allows user-specific tuning to a
variety of host-centric applications.
Point
Point
Point
Point
End
End
End
End
Figure 2. Fan-in/out Usage
Chip Set
Chip Set
Chip Set
Chip Set
x8
CPU
CPU
CPU
CPU
x8
PEX 8548
PEX 8548
PEX 8548
PEX 8548
x8 or x16
x4
Memory
Memory
Memory
Memory