LTM8022EV-PBF LINER [Linear Technology], LTM8022EV-PBF Datasheet - Page 9

• Manufacturer Part Number: LTM8022EV-PBF
• Description: 1A, 36V DC/DC ?Module
• Manufacturer: LINER [Linear Technology]

For most applications, the design process is straight
forward, summarized as follows:
1. In Table 1, fi nd the row that has the desired input volt-
2. Apply the recommended C
3. Connect BIAS as indicated.
While these component combinations have been tested for
proper operation, it is incumbent upon the user to verify
proper operation over the intended system’s line, load and
environmental conditions.
If the desired output voltage is not listed in Table 1, set
the output by applying an R
given by the equation R
R
operation over the system’s intended line, load and envi-
ronmental conditions.
Capacitor Selection Considerations
The C
minimum recommended values for the associated oper-
ating conditions. Applying capacitor values below those
indicated in Table 1 is not recommended, and may result
in undesirable operation. Using larger values is generally
acceptable, and can yield improved dynamic response, if
it is necessary. Again, it is incumbent upon the user to
verify proper operation over the intended system’s line,
load and environmental conditions.
Ceramic capacitors are small, robust and have very low
ESR. However, not all ceramic capacitors are suitable.
X5R and X7R types are stable over temperature and ap-
plied voltage and give dependable service. Other types,
including Y5V and Z5U, have very large temperature and
voltage coeffi cients of capacitance. In an application cir-
cuit they may have only a small fraction of their nominal
capacitance, resulting in much higher output voltage ripple
than expected.
Ceramic capacitors are also piezoelectric. In Burst Mode
operation, the LTM8022’s switching frequency depends
on the load current, and can excite a ceramic capacitor
at audio frequencies, generating audible noise. Since the
LTM8022 operates at a lower current limit during Burst
APPLICATIONS INFORMATION
ADJ
age range and output voltage.
is in kΩ and V
IN
and C
OUT
capacitor values in Table 1 are the
OUT
ADJ
is in volts. Verify the LTM8022’s
= 394.21/(V
IN
ADJ
, C
OUT
resistor whose value is
, R
OUT
ADJ
and R
– 0.79), where
T
values.
Mode operation, the noise is typically very quiet to a
casual ear.
If this audible noise is unacceptable, use a high per-
formance electrolytic capacitor at the output. The input
capacitor can be a parallel combination of a 2.2μF
ceramic capacitor and a low cost electrolytic capacitor.
A fi nal precaution regarding ceramic capacitors concerns
the maximum input voltage rating of the LTM8022. A
ceramic input capacitor combined with trace or cable
inductance forms a high Q (under damped) tank circuit.
If the LTM8022 circuit is plugged into a live supply, the
input voltage can ring to twice its nominal value, possi-
bly exceeding the device’s rating. This situation is easily
avoided; see the Hot-Plugging Safely section.
Frequency Selection
The LTM8022 uses a constant-frequency PWM architecture
that can be programmed to switch from 200kHz to 2.4MHz
by using a resistor tied from the R
provides a list of R
frequencies.
Table 2. Switching Frequency vs R
Operating Frequency Tradeoffs
It is recommended that the user apply the optimal R
value given in Table 1 for the input and output operating
condition. System level or other considerations, however,
may necessitate another operating frequency. While the
LTM8022 is fl exible enough to accommodate a wide range
SWITCHING FREQUENCY (MHz)
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.2
1.4
1.6
1.8
2.0
2.2
2.4
T
resistor values and their resultant
T
Value
T
pin to ground. Table 2
R
T
LTM8022
VALUE (kΩ)
88.7
68.1
56.2
46.4
40.2
29.4
23.7
19.1
16.2
13.3
11.5
9.76
8.66
187
121
34
8022fb
9
T