A290011TV-90 AMICC [AMIC Technology], A290011TV-90 Datasheet
A290011TV-90
Related parts for A290011TV-90
A290011TV-90 Summary of contents
Page 1
... Error Correction: P.8: Autoselect Command Sequence (line 15), XX11h → XX03h 1.0 Final version release 1.1 Add 32Pin Pb-Free TSOP package type for A290011UV-70(U)F & A290011TV-70(U)F 1.2 Add Pb-Free package type for all parts 1.3 Add sTSOP package type. (December, 2004, Version 1.3) 128K X 8 Bit CMOS 5.0 Volt-only, max. = 50µ ...
Page 2
Features 5.0V ± 10% for read and write operations Access times: - 55/70/90 (max.) Current typical active read current - 30 mA typical program/erase current - 1 µA typical CMOS standby Flexible sector architecture - 8 Kbyte/ ...
Page 3
The sector erase architecture allows memory sectors to be erased and reprogrammed without affecting the data contents of other sectors. The A29001 is fully erased when shipped from the factory. The hardware sector protection feature disables operations for both program ...
Page 4
Block Diagram VCC VSS State WE Control RESET (N/A A290011) Command Register CE OE VCC Detector A0-A16 Pin Descriptions (December, 2004, Version 1.3) Erase Voltage Generator PGM Voltage Generator STB Timer Pin No A16 Address Inputs I/O - ...
Page 5
Absolute Maximum Ratings* Ambient Operating Temperature . . . . .-55° 125°C Storage Temperature . . . . . . . . . . . . . . .-65° 150°C Ground to VCC . . . ...
Page 6
Requirements for Reading Array Data To read array data from the outputs, the system must drive the CE and OE pins the power control and IL selects the device the output control and ...
Page 7
Table 2. A29001/A290011 Top Boot Block Sector Address Table Sector A16 A15 SA0 0 0 SA1 0 1 SA2 1 0 SA3 1 1 SA4 1 1 SA5 1 1 SA6 1 1 Table 3. A29001/A290011 Bottom Boot Block Sector ...
Page 8
Sector Protection/Unprotection The hardware sector protection feature disables both program and erase operations in any sector. The hardware sector unprotection feature re-enables both program and erase operations in previously protected sectors. Sector protection/unprotection must be implemented using programming equipment. The ...
Page 9
Command Definitions Writing specific address and sequences into the command register initiates device operations. The Command Definitions table defines the valid register command sequences. Writing incorrect address and data values or writing them in the improper sequence resets the device ...
Page 10
START Write Program Command Sequence Data Poll from System Embedded Program algorithm in progress Verify Data ? Increment Address Last Address ? Programming Completed Note : See the appropriate Command Definitions table for program command sequence. Figure 2. Program Operation ...
Page 11
Embedded Program algorithm. Writing the Erase Suspend command during the Sector Erase time- out immediately terminates the time-out period and suspends the erase operation. Addresses are "don't cares" when ...
Page 12
Table 5. A29001/A290011 Command Definitions Command Sequence (Note 1) Read (Note 5) Reset (Note 6) Autoselect Manufacturer ID (Note 7) Device ID Top Bottom Continuation ID Sector Protect Verify (Note 8) Program Chip Erase Sector Erase Erase Suspend (Note 9) ...
Page 13
Write Operation Status Several bits, I/O , I/O , I/O , I/O , and I the A29001/A290011 to determine the status of a write operation. Table 6 and the following subsections describe the functions of these ...
Page 14
I/O : Toggle Bit I 6 Toggle Bit I on I/O indicates whether an Embedded 6 Program or Erase algorithm is in progress or complete, or whether the device has entered the Erase Suspend mode. Toggle Bit I may be ...
Page 15
I I/O is "1", the internally controlled 3 3 erase cycle has begun; all further commands (other than Erase Suspend) are ignored until the erase operation is complete. If I/O is "0", the device will ...
Page 16
Operation Standard Embedded Program Algorithm Mode Embedded Erase Algorithm Erase Reading within Erase Suspend Suspended Sector Mode Reading within Non-Erase Suspend Sector Erase-Suspend-Program Notes: 1. I/O and I/O require a valid address when reading status information. Refer to the appropriate ...
Page 17
DC Characteristics TTL/NMOS Compatible Parameter Parameter Description Symbol I Input Load Current LI I Input Load Current VCC = VCC Max, LIT A9, OE & RESET I Output Leakage Current LO I VCC Active Read Current CC1 (Notes 1, 2) ...
Page 18
AC Characteristics Read Only Operations Parameter Symbols JEDEC Std t t Read Cycle Time (Note 2) AVAV Address to Output Delay AVQV ACC t t Chip Enable to Output Delay ELQV Output Enable to ...
Page 19
Hardware Reset ( RESET (N/A on A290011) ) Parameter JEDEC Std t READY RESET Pin Low (During Embedded Algorithms) to Read or Write (See Note) t READY RESET Pin Low (Not During Embedded Algorithms) to Read or Write (See Note) ...
Page 20
AC Characteristics Erase and Program Operations Parameter Symbols JEDEC Std t t Write Cycle Time (Note 1) AVAV Address Setup Time AVWL Address Hold Time WLAX Data Setup Time DVWH DS ...
Page 21
Timing Waveforms for Program Operation Program Command Sequence (last two cycles Addresses 555h CE t GHWL Data t VCS VCC Note : PA = program addrss program data, Dout is the true ...
Page 22
Timing Waveforms for Chip/Sector Erase Operation Erase Command Sequence (last two cycles Addresses 2AAh CE t GHWL Data t VCS VCC Note : SA = Sector Address Valid Address for reading status ...
Page 23
Timing Waveforms for Data Polling (During Embedded Algorithms Addresses VA t ACC OEH WE I/O 7 I Note : VA = Valid Address. Illustation shows first status ...
Page 24
Timing Waveforms for Toggle Bit (During Embedded Algorithms Addresses VA t ACC OEH WE I Note Valid Address; not required for I/O read cycle, and ...
Page 25
Timing Waveforms for I/O vs. I/O 2 Enter Erase Embedded Suspend Erasing WE Erase Erase Suspend I/O 6 I/O 2 I/O and I/O toggle with OE and Note : Both I/O and I/O toggle with OE or ...
Page 26
Timing Waveforms for Alternate CE Controlled Write Operation 555 for program 2AA for erase Addresses GHEL Data for program 55 for erase Note : Program Address, ...
Page 27
Latch-up Characteristics Input Voltage with respect to VSS on all I/O pins VCC Current Input voltage with respect to VSS on all pins except I/O pins (including A9, OE and RESET ) Includes all pins except VCC. Test conditions: VCC ...
Page 28
Test Conditions Test Specifications Test Condition Output Load Output Load Capacitance, C (including jig capacitance) L Input Rise and Fall Times Input Pulse Levels Input timing measurement reference levels Output timing measurement reference levels Test Setup Device Under Test (December, ...
Page 29
... A29001TV-55F A290011TV-55 A290011TV-55F A29001TX-55 A29001TX-55F A290011TX-55 A290011TX-55F A29001T-70 A29001T-70F A290011T-70 A290011T-70F A29001TL-70 A29001TL-70F A290011TL-70 A290011TL-70F A29001TV-70 70 A29001TV-70F A290011TV-70 A290011TV-70F A290011TV-70UF A29001TX-70 A29001TX-70F A290011TX-70 A290011TX-70F A290011TX-70UF (December, 2004, Version 1.3) Active Read Program/Erase Current Current Typ. (mA) Typ. (mA A29001/A290011 Series Standby ...
Page 30
... Top Boot Sector Flash Part No. Access Time (ns) A29001T-90 A29001T-90F A290011T-90 A290011T-90F A29001TL-90 A29001TL-90F A290011TL-90 A290011TL-90F 90 A29001TV-90 A29001TV-90F A290011TV-90 A290011TV-90F A29001TX-90 A29001TX-90F A290011TX-90 A290011TX-90F Note for industrial operating temperature range (December, 2004, Version 1.3) Active Read Program/Erase Current Current Typ. (mA) Typ. (mA ...
Page 31
Ordering Information (continued) Bottom Boot Sector Flash Access Time Part No. (ns) A29001U-55 A29001U-55F A290011U-55 A290011U-55F A29001UL-55 A29001UL-55F A290011UL-55 A290011UL-55F 55 A29001UV-55 A29001UV-55F A290011UV-55 A290011UV-55F A29001UX-55 A29001UX-55F A290011UX-55 A290011UX-55F A29001U-70 A29001U-70F A290011U-70 A290011U-70F A29001UL-70 A29001UL-70F A290011UL-70 A290011UL-70F A29001UV-70 70 A29001UV-70F ...
Page 32
Ordering Information (continued) Bottom Boot Sector Flash Part No. Access Time (ns) A29001U-90 A29001U-90F A290011U-90 A290011U-90F A29001UL-90 A29001UL-90F A290011UL-90 A290011UL-90F 90 A29001UV-90 A29001UV-90F A290011UV-90 A290011UV-90F A29001UX-90 A29001UX-90F A290011UX-90 A290011UX-90F Note for industrial operating temperature range (December, 2004, Version ...
Page 33
Package Information P-DIP 32L Outline Dimensions Symbol Notes: 1. The maximum value of dimension D includes end flash. 2. Dimension E does not include resin fins. (December, 2004, Version 1. Base Plane ...
Page 34
Package Information PLCC 32L Outline Dimension Symbol Notes: 1. Dimensions D and E do not include resin fins. 2. Dimensions G design reference only. (December, 2004, Version 1. ...
Page 35
Package Information TSOP 32L TYPE 20mm) Outline Dimensions y Symbol Notes: 1. The maximum value of dimension D includes end flash. 2. Dimension E does not include resin fins. 3. Dimension S includes end flash. (December, 2004, ...
Page 36
Package Information sTSOP 32L TYPE 13.4mm) Outline Dimensions 0.076MM SEATING PLANE Symbol Notes: 1. The maximum value of dimension D 2. Dimension E does not include resin fins. 3. Dimension S includes end flash. (December, 2004, Version ...