ADG774 Analog Devices, ADG774 Datasheet - Page 4

• Manufacturer Part Number: ADG774
• Description: CMOS 3 V/5 V/ Wide Bandwidth Quad 2:1 Mux
• Manufacturer: Analog Devices

ABSOLUTE MAXIMUM RATINGS
(T
V
Analog, Digital Inputs
Continuous Current, S or D . . . . . . . . . . . . . . . . . . . . 100 mA
Peak Current, S or D . . . . . . . . . . . . . . . . . . . . . . . . . 300 mA
Operating Temperature Range
Storage Temperature Range . . . . . . . . . . . . . –65 C to +150 C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . +150 C
SOIC Package, Power Dissipation . . . . . . . . . . . . . . . . 600 mW
Lead Temperature, Soldering
QSOP Package, Power Dissipation . . . . . . . . . . . . . . . 566 mW
Lead Temperature, Soldering
ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 kV
NOTES
1
2
ADG774
Model
ADG774BR
ADG774BRQ
Stresses above those listed under Absolute Maximum Ratings may cause perma-
Overvoltages at IN, S or D will be clamped by internal diodes. Current should be
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the ADG774 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute maximum rating condi-
tions for extended periods may affect device reliability. Only one absolute maxi-
mum rating may be applied at any one time.
limited to the maximum ratings given.
DD
A
Industrial (B Version) . . . . . . . . . . . . . . . . . –40 C to +85 C
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . +215 C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . +220 C
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . +215 C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . +220 C
= +25 C unless otherwise noted)
JA
JA
to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +6 V
Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 100 C/W
Thermal Impedance . . . . . . . . . . . . . . . . . . . 149.97 C/W
PIN CONFIGURATION
GND
S1A
S1B
S2A
S2B
D1
D2
2
IN
. . . . . . . . . . . –0.3 V to V
1
2
3
4
5
6
7
8
(Pulsed at 1 ms, 10% Duty Cycle max)
(SOIC/QSOP)
(Not to Scale)
Temperature Range
–40 C to +85 C
–40 C to +85 C
TOP VIEW
ADG774
30 mA, Whichever Occurs First
16
15
14
13
12
11
10
1
9
V
EN
S4A
S4B
D4
S3A
S3B
D3
DD
DD
+ 0.3 V or
ORDERING GUIDE
Package Descriptions
R = 0.15" Small Outline IC (SOIC)
RQ = 0.15" Quarter Size Outline Package (QSOP)
–4–
V
GND
S
D
IN
EN
R
R
I
I
I
V
C
C
C
t
t
t
Crosstalk
Off Isolation A measure of unwanted signal coupling through an
Bandwidth
Distortion
ON
OFF
D
S
D
D
R
DD
ON
FLAT(ON)
D
S
D
D
, I
(OFF)
(OFF)
, C
ON
(OFF)
(V
(OFF)
S
S
(ON)
S
)
(ON) “ON” Switch Capacitance.
Frequency response of the switch in the ON
Most Positive Power Supply Potential.
Ground (0 V) Reference.
Source Terminal. May be an input or output.
Drain Terminal. May be an input or output.
Logic Control Input.
Logic Control Input.
Ohmic resistance between D and S.
On Resistance match between any two channels
i.e., R
Flatness is defined as the difference between the
maximum and minimum value of on resistance
as measured over the specified analog signal
range.
Source Leakage Current with the switch “OFF.”
Drain Leakage Current with the switch “OFF.”
Channel Leakage Current with the switch “ON.”
Analog Voltage on Terminals D, S.
“OFF” Switch Source Capacitance.
“OFF” Switch Drain Capacitance.
Delay between applying the digital control input
and the output switching on. See Test Circuit 4.
Delay between applying the digital control input
and the output switching Off.
“OFF” time or “ON” time measured between
the 90% points of both switches, when switching
from one address state to another. See Test
Circuit 5.
A measure of unwanted signal that is coupled
through from one channel to another as a result
of parasitic capacitance.
“OFF” switch.
state measured at 3 dB down.
R
FLAT(ON)
ON
TERMINOLOGY
max – R
/R
L
ON
WARNING!
min.
ESD SENSITIVE DEVICE
Package Options
R-16A
RQ-16
REV. 0