93AA76-P Microchip Technology, 93AA76-P Datasheet
93AA76-P
Related parts for 93AA76-P
93AA76-P Summary of contents
Page 1
... These devices also have a Program Enable (PE) pin to allow the user to write protect the entire contents of the memory array. The 93AA76/86 is available in standard 8-pin DIP and 8-pin surface mount SOIC packages. Microwire is a registered trademark of National Semiconductor Incorporated. 1996 Microchip Technology Inc. ...
Page 2
... ELECTRICAL CHARACTERISTICS 1.1 Maximum Ratings* V ..................................................................................7.0V CC All inputs and outputs w.r.t. V ............... -0.6V to Vcc +1.0V SS Storage temperature ..................................... -65˚C to +150˚C Ambient temp. with power applied................. -65˚C to +125˚C Soldering temperature of leads (10 seconds) ............. +300˚C ESD protection on all pins................................................4 kV *Notice: Stresses above those listed under “Maximum ratings” ...
Page 3
... ERASE/WRITE mode — ERAL mode — WRAL mode 10M — cycles (Note 2) Preliminary 93AA76/86 6. 4. 4.5V CC < 2. 6.0V, Relative to CLK CC V 4.5V, Relative to CLK CC V 2.5V, Relative to CLK ...
Page 4
... WRAL EWDS TABLE 1-5: INSTRUCTION SET FOR 93AA76: ORG=0 (X8 ORGANIZATION) Instruction SB Opcode READ EWEN ...
Page 5
... Erase/Write Enable and Disable (EWEN, EWDS) , the x16 orga- The 93AA76/86 powers up in the Erase/Write Disable (EWDS) state. All programming modes must be pre- ceded by an Erase/Write Enable (EWEN) instruction. Once the EWEN instruction is executed, programming remains enabled until an EWDS instruction is executed removed from the device ...
Page 6
... DEVICE OPERATION 3.1 READ The READ instruction outputs the serial data of the addressed memory location on the DO pin. A dummy zero bit precedes the 16 bit (x16 organization bit (x8 organization) output string. The output data bits will toggle on the rising edge of the CLK and are stable after the specifi ...
Page 7
... Microchip Technology Inc CKH CKL T DIH STATUS VALID ... ... ... ORG X’s CC ORG X’s SS ... ORG X’s CC ORG X’S SS Preliminary 93AA76/86 T CSH CSL ... CSL T CSL X DS21130C-page 7 ...
Page 8
... FIGURE 3-5: WRITE CS CLK HIGH IMPEDANCE DO FIGURE 3-6: WRAL CS CLK HIGH IMPEDANCE DO ORG X’s CC Guaranteed at Vcc = +4.5V to +6.0V. ORG X’s SS FIGURE 3-7: ERASE CS CLK HIGH IMPEDANCE DO DS21130C-page 8 ... ... ... ... ... Preliminary STANDBY ...
Page 9
... RESET status. 4.2 Serial Clock (CLK) The Serial Clock is used to synchronize the communi- cation between a master device and the 93AA76/86. Opcode, address, and data bits are clocked in on the positive edge of CLK. Data bits are also clocked out on the positive edge of CLK. ...
Page 10
... NOTES: DS21130C-page 10 Preliminary 1996 Microchip Technology Inc. ...
Page 11
... Product Identification System To order or to obtain information, e.g., on pricing or delivery, please use the listed part numbers, and refer to the factory or the listed sales offices. 93AA76/86 – /P Package: Temperature Range: Device: Sales and Support Products supported by a preliminary Data Sheet may possibly have an errata sheet describing minor operational differences and recommended workarounds ...
Page 12
... Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. No repre- sentation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip’s products as critical components in life support systems is not autho- rized except with express written approval by Microchip ...