ISPGDX160-5B272 Lattice Semiconductor, ISPGDX160-5B272 Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/3/381/lattice_semiconductor_sml.jpg)
ISPGDX160-5B272
Manufacturer Part Number
ISPGDX160-5B272
Description
In-System Programmable Generic Digital CrosspointTM
Manufacturer
Lattice Semiconductor
Datasheet
1.ISPGDX160-5B272.pdf
(25 pages)
ing Pool (GRP). All I/O pin inputs enter the GRP directly
or are registered or latched so they can be routed to the
required I/O outputs. I/O pin inputs are defined as four
sets (A,B,C,D) which have access to the four MUX inputs
found in each I/O cell. Each output has individual, pro-
grammable I/O tri-state control (OE), output latch clock
(CLK) and two multiplexer control (MUX0 and MUX1)
inputs. Polarity for these signals is programmable for
each I/O cell. The MUX0 and MUX1 inputs control a fast
4:1 MUX, allowing dynamic selection of up to four signal
sources for a given output. OE, CLK and MUX0 and
MUX1 inputs can be driven directly from selected sets of
I/O pins. Optional dedicated clock input pins give mini-
mum clock-to-output delays.
Through in-system programming, connections between
I/O pins and architectural features (latched or registered
inputs or outputs, output enable control, etc.) can be
defined. In keeping with its data path application focus,
the ispGDX devices contain no programmable logic
arrays. All input pins include Schmitt trigger buffers for
noise immunity. These connections are programmed
into the device using non-volatile E
Non-volatile technology means the device configuration
is saved even when the power is removed from the
device.
Table 1. ispGDX Family Members
Description (Continued)
* The CLK, OE, MUX0 and MUX1 terminals on each I/O cell can each access 25% of the I/Os.
** MUXed with Y1.
I/O Pins
I/O-OE Inputs*
I/O-Clk Inputs*
I/O-MUXsel1 Inputs*
I/O-MUXsel2 Inputs*
Dedicated Clock Pins
BSCAN / ISP Interface
RESET
Power/GND
Pin Count/Package
BSCAN / ispEN
TOE
2
CMOS technology.
100-Pin TQFP
ispGDX80A
1**
80
20
20
20
20
12
2
1
4
1
2
Specifications ispGDX Family
In addition, there are no pin-to-pin routing constraints for
1:1 or 1:n signal routing. That is, any I/O pin configured
as an input can drive one or more I/O pins configured as
outputs.
The device pins also have the ability to set outputs to
fixed HIGH or LOW logic levels (Jumper or DIP Switch
mode). Device outputs are specified for 24mA sink and
source current and can be tied together in parallel for
greater drive. Programmable output slew rate can be
defined independently for each I/O pin to reduce overall
ground bounce and switching noise.
All I/O pins are equipped with IEEE1149.1-compliant
Boundary Scan Test circuitry for enhanced testability. In
addition, in-system programming is supported through
the Test Access Port via a special set of private com-
mands or through Lattice’s industry-standard ISP protocol.
The BSCAN/ispEN pin is used to make this selection.
The ispGDX I/Os are designed to withstand “live inser-
tion” system environments. The I/O buffers are disabled
during power-up and power-down cycles. When design-
ing for “live insertion,” absolute maximum rating conditions
for the Vcc and I/O pins must still be met. For additional
information, an application note about using Lattice de-
vices in hot swap environments can be downloaded from
the Lattice web site at www.latticesemi.com.
ispGDX DEVICE
176-Pin TQFP/
160-Pin PQFP
ispGDX120A
120
30
30
30
30
25
4
1
1
4
1
208-Pin PQFP
ispGDX160/A
272-Ball BGA
160
40
40
40
40
33
4
1
1
4
1