AM79C983A Advanced Micro Devices, AM79C983A Datasheet - Page 31
![no-image](/images/manufacturer_photos/0/0/14/advanced_micro_devices_sml.jpg)
AM79C983A
Manufacturer Part Number
AM79C983A
Description
Integrated Multiport Repeater 2 (IMR2)
Manufacturer
Advanced Micro Devices
Datasheet
1.AM79C983A.pdf
(60 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AM79C983AKC
Manufacturer:
AMD
Quantity:
20 000
Total Octets
Address:
This is a 4-byte attribute register whose contents are in-
cremented while the repeater is repeating packet data.
This counter is a truncated divide by 8 of the total num-
ber of bits transmitted by the repeated (i.e., the number
of whole bytes transmitted by the repeater). The
counter counts the bytes on all non-collision packets
with a valid Start of Frame Delimiter (SFD). The pre-
amble is included in the count. The four bytes in this at-
tribute are sequentially accessed by reading the D
register, LSB first. Note that once the C register is pro-
grammed for access to this attribute, reading the D reg-
ister port causes the value of this register to be copied
into the holding register. The data is then read off the
holding register, without affecting this attribute. This se-
quence is repeated when the last byte is read and the
D register is accessed.
Transmit Collisions
Address:
This is a 4-byte attribute whose contents are incre-
mented each time the repeater has entered the trans-
mit collision state from any state other than ONE PORT
LEFT. The bytes are read in LOW to HIGH order by
reading the Data (D) register consecutively. The se-
quence will be restarted once the last byte is read or
the C register is reprogrammed with this register num-
ber. This causes the current value of the counter to be
copied into a holding register, which is then read by ac-
cessing the D register.
Configuration Register
Address:
This is a read/write register. The value read is the
same as that written. Unused bits are read as zeros
and only zeros should be written into these bits. Do
not write non-zero values into unused bits. All bits are
cleared upon reset.
Byte 0
Byte 1
Byte 2
Byte 3
Byte 0
Byte 1
Byte 2
Byte 3
MSB
bit 7
bit 31
bit 7
bit 31
D Port Read/Write
D Port Read/Write
M
SB
1110 1100
1110 1101
1111 0000
P R E L I M I N A R Y
bit 0
bit 24
bit 0
bit 24
LSB
LSB
Am79C983A
I
S
Repeater Status
Address:
This is a read only register. Bit 0 is the only bit of inter-
est. When bit 0 is set, the IMR2 device has entered
MAU Jabber Lockup Protection (MJLP). The Repeater
Status register is cleared by reading.
QuIET Device Transceiver ID Register
Address:
This is a read-only register. It contains the transceiver
ID of the QuIET device connected to the IMR2 device.
The 16-bit quantity has the following format:
This 16-bit register is divided into four sections. Each
section is labeled M
ceivers 0 through 3. These register bits are only valid if
the appropriate Transceiver Interface Status Register
bit indicates that a QuIET device is connected.
Byte 0
Byte 1
MSB
I
0
D Port Read/Write
D Port Read
MSB
Transceiver 0
Transceiver 1
Transceiver 2
Transceiver 3
Enable Interrupts. When this bit is set to 0 all inter-
rupts from this IMR2 device are masked (but not
cleared) and the INT output pin is forced into inac-
tive state (not driven).
Source Address Match Interrupt Enable. When this
bit is set, IMR2 device will generate an interrupt if
the Source Address of the received packet match-
es that which is programmed into the Source Ad-
dress Match Register.
M
M
MSB
D Port Read
0
0
13
33
Transceiver 1
Transceiver 3
1111 1010
E
0
1
1111 1011
M
M
S
0
12
32
M
M
X3
11
31
0
0
to M
M
M
Status
No Error
Error
PAUI [3:0]
PAUI [7:4]
PAUI [11:8]
AUI and RAUI ports or misc.
10
30
0
0
X0
M
M
where X refers to trans-
03
23
Transceiver 0
Transceiver 2
0
0
M
M
02
22
0
0
M
M
01
21
M
M
0
E
LSB
LSB
LSB
00
20
31