FTR-K1-17A FUJITSU [Fujitsu Component Limited.], FTR-K1-17A Datasheet

Page 1

... Nominal Voltage (e) Contact Material Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-K1CK012W 005 T (d) (e) FTR-KT : FTR-KT Series A : Vertical J : Horizontal K : Standard (400mW) / flux free 005 : 5 VDC, 006 : 6VDC, 018 : 18 VDC 022 :022VDC 024 : 24VDC 048 : 48VDC T : AgSnO2 Actual marking: K1CK012W FTR-K1 SERIES RoHS compliant 009 : 9VDC 012 : 12VDC 028 : 28VDC  ...

Page 2

... Note: All values in the table are measured at 20°C. *1: No contact current at 20°C *2: Specified values are subject to pulse wave voltage FTR-K1 SERIES Coil Tab Terminal Coil Power Voltage 400 mW A: Vertical 430 400 mW ...

Page 3

... Shock Misoperation Resistance Endurance Weight *  Need to consider the heat from PCB when max. current is more than 10A Minimum switching loads mentioned above are reference values. Please perform the confirmation test with the actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. FTR-K1 SERIES FTR-K form A AgSnO2 Maximum 100 mΩ VDC 17 A, 250 VAC 17 A 78A, 120VAC (lamp load) 4,250VA 440 VAC VDC 400mW (at 430mW 48V coil) 200 mW (210mW at 48V coil) -40ºC to +105ºC (no frost) ...

Page 4

... UL UL 508 E63614 CSA C22.2 No 40304 VDE 0435, 0631, 0700, 0860, 40013848 SEMKO EN 61058-1:1992 and A1 EN 61095:1993 and A1+A11 Complies with NEMKO, DEMKO, FIMKO FTR-K1 SERIES FTR-KT Minimum 1,000 MΩ 1 min. 1,000 VAC (50/60 Hz) 1 min. 5,000 VAC (50/60 Hz) 1 min. 10,000 250 V 3 IIIa Contact rating FTR-K Flammability: UL 94-V0 (plastics) 17A, 277 VAC (resistive) ...

Page 5

... Coil Power (W) Life Curve 1000 1000 FTR-K1TAK AC250V 500 AC250V cosφ=0. 300 200 100 AC250V cosφ=0 Contact Current Load (A) FTR-K1 SERIES Operating Range 2.5 FTR-K 17A 1 100 Ambient temperature (ºC) Distribution of Operation & Release Voltage 100 FTR-K1TAK012T N=100 90 Operate ...

Page 6

... Dimensions FTR-KTJK Pre- 0.8 solder (2.6) φ 0.45 37.5 29 40.5 +0.3 44.5 +0.3 A6.3-0.8 DIN 46244 (#250) ±0.1 0.8 0.8 0.8 (2.6) 5 7.5 12.7 +0.3 A6.3-0.8 DIN 46244 (#250) (2.6) 0.8 0.8 0.8 5 7.5 12.7 FTR-K1 SERIES l Schematics (BOTTOM VIEW) NO COM Orientation mark PC board mounting l hole layout (BOTTOM VIEW) 37.5 5 ±0.1 2-φ1 4-φ1.3 -0 (30.2) l Schematics (BOTTOM VIEW) NO COM Orientation mark PC board mounting l hole layout (BOTTOM VIEW) 37.5 5 ±0.1 2-φ1 4-φ1.3 -0 (30.2) Unit ...

Page 7

... Soldering: dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity Moisture Sensitivity Level standard is not applicable to electromechanical realys Tin Whisker Dipped SnAgCu solder is known as low risk tin whisker. No considerable length whisker was found by our in l house test. FTR-K1 SERIES  ...

Page 8

... Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://www.fujitsu.com/us/services/edevices/components/ ©2008 Fujitsu Components America, Inc. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. Fujitsu Components America or its affiliates do not warrant that the content of datasheet is error free continuing effort to improve our products Fujitsu Components America, Inc. or its affiliates reserve the right to change specifications/datasheets without prior notice. Rev. August 6, 2008. FTR-K1 SERIES Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu ...