74ABT373CSC Fairchild Semiconductor, 74ABT373CSC Datasheet - Page 7

• Manufacturer Part Number: 74ABT373CSC
• Description: IC OCT TRANSP LATCH 3ST 20SOIC
• Manufacturer: Fairchild Semiconductor
• Series: 74ABTr

Specifications of 74ABT373CSC

• Logic Type: D-Type Transparent Latch
• Circuit: 8:8
• Output Type: Tri-State
• Voltage - Supply: 4.5 V ~ 5.5 V
• Independent Circuits: 1
• Delay Time - Propagation: 2.7ns
• Current - Output High, Low: 32mA, 64mA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 20-SOIC (7.5mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

©1993 Fairchild Semiconductor Corporation
74ABT373 Rev. 1.4
Skew
SOIC package.
Notes:
11. This specification is guaranteed but not tested. The limits represent propagation delays with 250 pF load capacitors
12. This specification is guaranteed but not tested. The limits apply to propagation delays for all paths described
13. Skew is defined as the absolute value of the difference between the actual propagation delays for any two separate
14. Propagation delay variation is for a given set of conditions (i.e., temperature and V
15. This describes the difference between the delay of the LOW-to-HIGH and the HIGH-to-LOW transition on the same
Capacitance
Note:
16. C
Symbol
t
t
OSHL
OSLH
t
in place of the 50pF load capacitors in the standard AC load.
switching in phase (i.e., all LOW-to-HIGH, HIGH-to-LOW, etc.).
outputs of the same device. The specification applies to any outputs switching HIGH-to-LOW (t
(t
but not tested.
specification is guaranteed but not tested.
pin. It is measured across all the outputs (drivers) on the same chip, the worst (largest delta) number is the
guaranteed specification. This specification is guaranteed but not tested.
Symbol
C
OST
t
t
PS
PV
OSLH
OUT
OUT
C
(15)
(14)
(13)
IN
(13)
(13)
(16)
), or any combination switching LOW-to-HIGH and/or HIGH-to-LOW (t
is measured at frequency f = 1MHz, per MIL-STD-883, Method 3012.
Pin to Pin Skew,
HL Transitions
Pin to Pin Skew,
LH Transitions
Duty Cycle, LH–HL Skew
Pin to Pin Skew,
LH/HL Transitions
Device to Device Skew,
LH/HL Transitions
Input Capacitance
Output Capacitance
Parameter
Parameter
8 Outputs Switching
T
A
V
= –40°C to +85°C,
V
V
CC
CC
CC
C
= 4.5V–5.5V,
L
= 0V
= 5.0V
7
Max.
= 50pF,
1.0
1.0
1.4
1.5
2.0
Conditions
T
A
= 25°C
(11)
8 Outputs Switching
OST
T
A
V
). This specification is guaranteed
= –40°C to +85°C,
CC
CC
C
L
= 4.5V–5.5V,
) from device to device. This
= 250pF,
Max.
1.5
1.5
3.5
3.9
4.0
Typ.
5
9
OSHL
), LOW-to-HIGH
(12)
www.fairchildsemi.com
Units
pF
pF
Units
ns
ns
ns
ns
ns