PCM-5862E ETC [List of Unclassifed Manufacturers], PCM-5862E Datasheet - Page 27
PCM-5862E
Manufacturer Part Number
PCM-5862E
Description
All in one multi-media Pentium processor-based single board computer
Manufacturer
ETC [List of Unclassifed Manufacturers]
Datasheet
1.PCM-5862E.pdf
(108 pages)
- Current page: 27 of 108
- Download datasheet (587Kb)
Floppy drive connector (CN18)
You can attach up to two floppy drives to the PCM-5862E/
5862EL’s on-board controller. You can use any combination of 5¼”
(360 KB and 1.2 MB) and/or 3½” (720 KB, 1.44 MB, and 2.88
MB) drives.
A 34-pin daisy-chain drive connector cable is required for a dual-
drive system. On one end of the cable is a 34-pin flat-cable
connector. On the other end are two sets of floppy disk drive
connectors. Each set consists of a 34-pin flat-cable connector
(usually used for 3½” drives) and a printed-circuit board connector
(usually used for 5¼” drives).
Connecting the floppy drive
1. Plug the 34-pin flat-cable connector into CN18. Make sure that
2. Attach the appropriate connector on the other end of the cable to
3. If you are connecting a 5¼” floppy drive, line up the slot in the
If you need to make your own cable, you can find the pin
assignments for the board’s connector in Appendix C.
the red wire corresponds to pin one on the connector.
the floppy drive(s). You can use only one connector in the set.
The set on the end (after the twist in the cable) connects to the
A: drive. The set in the middle connects to the B: drive.
printed circuit board with the blocked-off part of the cable
connector.
If you are connecting a 3½” floppy drive, you may have trouble
determining which pin is pin number one. Look for a number
printed on the circuit board indicating pin number one. In
addition, the connector on the floppy drive connector may have
a slot. When the slot is up, pin number one should be on the
right. Check the documentation that came with the drive for
more information.
If you desire, connect the B: drive to the connectors in the
middle of the cable as described above.
Chapter 2 Installation
19
Related parts for PCM-5862E
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Installation Wiring Kit for PCM-9550F/PCM-9550L
Manufacturer:
ADVANTECH [Advantech Co., Ltd.]
Datasheet:
Part Number:
Description:
Installation Wiring Kit for PCM-9575/ PCM-9577F
Manufacturer:
ADVANTECH [Advantech Co., Ltd.]
Datasheet:
Part Number:
Description:
Installation Wiring Kit for PCM-9580F/PCM-9580FG
Manufacturer:
ADVANTECH [Advantech Co., Ltd.]
Datasheet:
Part Number:
Description:
Installation Wiring Kit for PCM-9582/PCM-9587
Manufacturer:
ADVANTECH [Advantech Co., Ltd.]
Datasheet:
Part Number:
Description:
Installation Wiring Kit for PCM-9576F
Manufacturer:
ADVANTECH [Advantech Co., Ltd.]
Datasheet:
Part Number:
Description:
Installation Wiring Kit for PCM-9576FV
Manufacturer:
ADVANTECH [Advantech Co., Ltd.]
Datasheet:
Part Number:
Description:
Installation Wiring Kit for PCM-9578
Manufacturer:
ADVANTECH [Advantech Co., Ltd.]
Datasheet:
Part Number:
Description:
Installation Wiring Kit for PCM-9577FG
Manufacturer:
ADVANTECH [Advantech Co., Ltd.]
Datasheet:
Part Number:
Description:
Installation Wiring Kit for PCM-9572
Manufacturer:
ADVANTECH [Advantech Co., Ltd.]
Datasheet:
Part Number:
Description:
Installation Wiring Kit for PCM-9584
Manufacturer:
ADVANTECH [Advantech Co., Ltd.]
Datasheet:
Part Number:
Description:
256Kb FRAM Serial 3V Memory
Manufacturer:
ETC [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
INFRARED REMOTE CONTROL TRANSMITTER
Manufacturer:
ETC [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
Adjustable Shunt Regulator
Manufacturer:
ETC [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
STEERING DIODE (RAIL CLAMP) ARRAY
Manufacturer:
ETC [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
MICROCONTROLLER BLOCK DIAGRAM
Manufacturer:
ETC [List of Unclassifed Manufacturers]
Datasheet: